The file 'Working 5 Speed Transmission Model For Toyota 22RE Engine 3D Printer Model' is (stl,xls,pdf,STL) file type, size is 6.3MB.
All my models are printed on a Prusa i3 kit. You can find the one I use by clicking the link below. You can get 15% off by using code "GBTE"
Tronxy Prusa I3
This is the 5 speed transmission that comes bolted to the back of a 22RE. This is the 4WD version of the transmission so it has a mounting surface to bolt a transfer case to. The transfer case will be the next thing I will upload
Fully working. All 5 speeds plus reverse. It uses a good amount of 3mm rod and 623zz bearings. M2.5 x 5mm set screws and nuts were used due to the small size of some of the parts.
| 2_shift_collar_fork_-_Scaled.stl | 557.3KB | |
| 2_shift_fork_-_Scaled.stl | 34.0KB | |
| 4_Shift_Collar_fork_-_Scaled.stl | 530.9KB | |
| 4_shift_fork_2_-_Scaled.stl | 40.2KB | |
| 5th_gear_Shift_collar_-_Scaled.stl | 157.7KB | |
| Bell_Housing_-_Scaled.stl | 4.9MB | |
| Front_bearing_retainer_-_Scaled.stl | 492.8KB | |
| Gear_1_Counter_Shaft_-_Scaled.stl | 744.2KB | |
| Gear_1_Top_-_Scaled.stl | 932.6KB | |
| Gear_2_Counter_shaft_-_Scaled.stl | 580.2KB | |
| Gear_2_Top_-_Sclaed.stl | 1009.1KB | |
| Gear_3_Counter_shaft_-_Scaled.stl | 676.1KB | |
| Gear_3_Top_-_Scaled.stl | 1018.0KB | |
| Gear_4_Counter_shaft_-_Scaled.stl | 647.4KB | |
| Gear_4_Top_-_Scaled.stl | 1006.3KB | |
| Gear_5_Counter_shaft_-_Scaled.stl | 984.5KB | |
| Gear_5_Top_-_Scaled.stl | 542.6KB | |
| Input_Shaft_-_Scaled.stl | 171.5KB | |
| Output_shaft_-_Scaled.stl | 178.0KB | |
| Parts_List.xls | 23.0KB | |
| Pressure_Plate_-_Scaled.stl | 330.7KB | |
| Reverse_Gear_-_Scaled.stl | 164.7KB | |
| Reverse_idler_-_Scaled.stl | 81.1KB | |
| R_shift_fork_-_Sclaed.stl | 429.2KB | |
| Section_one_breakdown_-_Bill_of_Materials_-_Sheet1.pdf | 283.4KB | |
| Section_two_breakdown_-_Sheet1.pdf | 390.5KB | |
| Shifter_ball_bottom_-_Scaled.stl | 200.8KB | |
| Shifter_ball_top_-_Scaled.stl | 169.5KB | |
| Shifter_base_-_Scaled.stl | 95.5KB | |
| Shifter_base_1_-_Scaled.stl | 413.1KB | |
| Shifter_base_2_-_Scaled.stl | 365.3KB | |
| Shift_Collar_-_Scaled.stl | 194.2KB | |
| Shift_collar_gear_-_5th_-_Scaled.stl | 88.3KB | |
| Shift_collar_gear_-_Scaled.stl | 69.1KB | |
| Shift_linkage_-_Scaled.stl | 70.2KB | |
| Shift_linkage_-_Sheet1.pdf | 200.0KB | |
| test_jig.STL | 323.9KB | |
| Transmission_Housing_1_-_Scaled.stl | 3.1MB | |
| Transmission_Housing_1_Cover_-_Scaled.stl | 2.2MB | |
| Transmission_housing_2_-_Scaled.stl | 318.4KB | |
| Transmission_housing_2_bearing_retainer_-_Sclaed.stl | 93.2KB | |
| Transmission_housing_3_-_Scaled.stl | 3.3MB | |
| Transmission_housing_3_-_Shell_-_cover_-_Scaled.stl | 714.0KB | |
| Transmission_Stand_-_Scaled.stl | 127.4KB |
