Wallace G1 3D Printer 3D Printer Model
The file 'Wallace G1 3D Printer 3D Printer Model' is (stl,scad) file type, size is 324.8KB.
The file 'Wallace G1 3D Printer 3D Printer Model' is (stl,scad) file type, size is 324.8KB.
NOTE! Upgraded Bed Mounts. Stiffer than previous mounts. May 1 2015
Based on the original Wallace design by whosawhatsis.
With all the Upgrades I've added to mine.
Rack & Pinion X & Y drives.
Spool Hook and Motor stabalizer ends.
Filament guide.
Y-Linerbearings removed from motor blocks
End Stop switch mounts.
And new here, Printable Bed! No board nessessary!
Onlything not included here is the Extruder. I recomend thing:40002 ;)
Current print area: 200x180x200
When I get the longer Y Rods: 200x200x200. That will come with new Bed Rear parts.
BOM and Build instructions started at :
http://gkprotoforms.ca
in How-To section.
| Arduino_Mount_WG1.stl | 321.0KB | |
| feet.stl | 171.0KB | |
| FilamentGuide.stl | 49.3KB | |
| New_Bed_Mounts.scad | 12.7KB | |
| New_Bed_Mounts_TFleft.stl | 40.4KB | |
| New_Bed_Mounts_TFlower.stl | 82.1KB | |
| New_Bed_Mounts_TFright.stl | 21.5KB | |
| New_Bed_Mounts_TRleft.stl | 21.9KB | |
| New_Bed_Mounts_TRlower.stl | 81.7KB | |
| New_Bed_Mounts_TRright.stl | 40.8KB | |
| New_Spring_Top.stl | 26.9KB | |
| pinion_herringbone_small_collar_keyed.stl | 182.7KB | |
| rack_herringbone_Wallace_Bed.stl | 285.7KB | |
| wallaceG1.scad | 35.7KB | |
| wallaceG1BaseEnd.stl | 82.7KB | |
| wallaceG1BedFoot.stl | 82.3KB | |
| wallaceG1Hook_Foot.stl | 15.6KB | |
| wallaceG1Hook_Top__repaired_.stl | 50.4KB | |
| wallaceG1Motor_Foot.stl | 37.6KB | |
| wallaceG1MSpacer.stl | 18.2KB | |
| wallaceG1_EndStop.stl | 43.3KB | |
| wallaceG1_X_Carriage.stl | 196.7KB | |
| wallaceG1_X_End_Right.stl | 134.4KB | |
| wallaceG1_X_Rack_mounts.stl | 47.5KB | |
| wallaceG1_Y_Bearing_Holder.stl | 49.7KB | |
| wallaceG1_Y_Bearing_Holder2.stl | 33.2KB | |
| wallaceG1_Y_Bearing_Switch_Holder.stl | 60.9KB | |
| wallaceG1_Y_Bearing_Switch_Holder2.stl | 44.4KB | |
| wallaceG1_Y_Bearing_Switch_Holder__repaired_.stl | 20.0KB | |
| wallaceG1_Y_Motor_Mount.stl | 59.1KB | |
| Wallace_G1_X-Rack_mounts.scad | 157.0B | |
| x_end_left.stl | 133.6KB | |
| Z_-_Half_Coupler_v3.stl | 607.5KB | |
| z_top_clamps.stl | 51.4KB |
