Upgrading PET Strip Cutting 3D Printer Model
The file 'Upgrading PET Strip Cutting 3D Printer Model' is (stl) file type, size is 7.3MB.
The file 'Upgrading PET Strip Cutting 3D Printer Model' is (stl) file type, size is 7.3MB.
Screws 4mm X 65 mm with nuts X 2
Screws 4 mm X 60 mm with nuts X 2
screws 4 mm X 15 mm with nuts X
12 volt Dc motor body outer diameter 34 mm
8 mm metal rod X 51 mm ( not 3d printed )
2 X Push buttons
2 X single pole double through ( 5 pin ) relays 12 volts
3 mm X 21 mm metal rod for inforcing spool drive gear
4 X 607 bearings
2 X 608 bearings
2 X 6202 bearings, jam them with epoxy after sharpening
4 X 608 bearings.
2 X mk 8 threaded rod length shown in the video with 6 nuts,
1X rod 7 mm or 8 mm, length should be greater than bottle height.
4 X 4 mm X 54 mm nut bolts as required.
3 bearings 607 for bearing body.( for 8.5 mm width)
4 X 15 mm screws with nuts for base fitting
2 X 4mm X 30mm screws with nuts
| 2.5mm_shaft_10_teeth_1.stl | 295.0KB | |
| 2nd_drive_gear_base.stl | 197.9KB | |
| 608_BEARING_FITTING.stl | 246.7KB | |
| 608_TOP_BEARING_FITTING.stl | 358.5KB | |
| 6202_bearing_busning_2_pcs.stl | 1.2MB | |
| Back_base_bracket.stl | 229.2KB | |
| base.stl | 797.7KB | |
| base_fitting_1_1.stl | 274.9KB | |
| base_fitting_2_1.stl | 268.6KB | |
| Bottom_bearing_fitting.stl | 255.0KB | |
| Front_base_bracket.stl | 229.2KB | |
| GEAR_60_TEETH_MOTOR_SIDE.stl | 1.4MB | |
| GEAR_60_TEETH_SPOOL_SIDE.stl | 1.1MB | |
| MAIN_SPOOL.stl | 424.5KB | |
| Metal_rod_8_mm_X_51_mm.stl | 30.4KB | |
| Motor_drive_gear.stl | 1.1MB | |
| MOTOR_GEAR_12_TEETH.stl | 297.5KB | |
| M_spacer.stl | 120.0KB | |
| new_bearing_body.stl | 3.9MB | |
| PLANETRARY_GEAR_24_TEETH.stl | 529.8KB | |
| rod_spacer_1.stl | 56.3KB | |
| r_h_s__bearing_body.stl | 3.8MB | |
| spacer_4_pcs.stl | 56.3KB | |
| spool_drive_base.stl | 349.3KB | |
| spool_drive_gear.stl | 335.6KB | |
| spool_middle.stl | 187.6KB | |
| spool_side.stl | 352.1KB | |
| Spur_gear_10_teeth.stl | 242.9KB | |
| Spur_gear_24_teeth_X_4_pcs.stl | 529.8KB | |
| Spur_gear_25_teeth.stl | 580.6KB | |
| Spur_gear_34_teeth.stl | 1.2MB | |
| Switch_body.stl | 387.1KB | |
| Switch_panal_back_cover.stl | 176.3KB | |
| Top_body.stl | 822.6KB | |
| Top_body_bearing_fitting_2.stl | 297.0KB |
