“Ugly” Stick Plane 1166mm Wing Span 3D Printer Model
The file '“Ugly” Stick Plane 1166mm Wing Span 3D Printer Model' is (stl,zip) file type, size is 178.4MB.
The file '“Ugly” Stick Plane 1166mm Wing Span 3D Printer Model' is (stl,zip) file type, size is 178.4MB.
UPDATE: new version of the tail assembly with stronger hinges and slightly reduced weight
This is my version of the classic "ugly" stick RC planes, the prototype is built but it has not been flown too date, I will post flight video as soon as possible. This design is based on some of my previous designs, https://www.thingiverse.com/thing:2145201 and https://www.thingiverse.com/thing:2022750.
Filght video can be seen at https://youtu.be/wi2N7e6ffDM
I apologize it's not the greatest quality video
This plane has an 1166mm wing span (46 inch), cg is between 48mm and 65mm(1 7/8 inch to 2 ¼ inch) from the leading edge, dry weight 1200g(2.65lbs) & all up flying weight should be around 1500 to 1650 grams (3.3 to 3.6 lbs.) using : https://hobbyking.com/en_us/turnigy-d2836-8-1100kv-brushless-outrunner-motor.html or https://hobbyking.com/en_us/turnigy-d3530-14-1100kv-brushless-outrunner-motor.html with a 9 X 6 prop, a 2200mAh 60C battery, a 40A ESC, and 4 X Tower Pro MG90S servos, or similar.
All my printing for this plane was done on my Prusa I3 with PLA at 233deg C (better layer adhesion, may not work with all printers test first) on a glass bed heated to 65deg C, print cooling is disabled & print head cooling is 100%, my printer is semi enclosed (most of the top is open) this prevents drafts and allows much more consistent prints. The glass is coated with an ABS slurry and everything is printed at 0.20mm layers with a 0.35mm tip, extrusion widths are set to 0.37mm. This plane will probably exceed 100 hours of printing time and use just over 1.2kg of filament. I have included g-code files that work with my Prusa I3 and my profile files for Cura 2.5.
| aileron_left_center__outer.stl | 2.1MB | |
| aileron_left_w_control_horn.stl | 3.0MB | |
| aileron_right_center__outer.stl | 2.1MB | |
| aileron_tip_inner.stl | 849.7KB | |
| aileron_tip_outer.stl | 878.8KB | |
| battery_cover.stl | 2.0KB | |
| elevator_joiner.stl | 2.2KB | |
| Elevator_L.stl | 759.1KB | |
| Elevator_L_R5.stl | 714.2KB | |
| Elevator_R_w_control_horn.stl | 1.2MB | |
| Elevator_R_w_control_horn_R5.stl | 1.2MB | |
| ESC_cover.stl | 1.8KB | |
| Fuslage_-_rear_-_1.stl | 1.2MB | |
| gear_mount.stl | 186.0KB | |
| gear_right.stl | 1.9MB | |
| H-stab_joiner.stl | 11.6KB | |
| H-stab_L.stl | 583.2KB | |
| H-stab_L_R5.stl | 639.5KB | |
| H-stab_R.stl | 583.2KB | |
| H-stab_R_R5.stl | 633.3KB | |
| hinge_plates_double.stl | 78.8KB | |
| hinge_plates_single.stl | 65.8KB | |
| nose.stl | 2.0MB | |
| Rudder.stl | 959.9KB | |
| Rudder_R5.stl | 936.1KB | |
| tail_R5.zip | 14.8MB | |
| tail_wheel_housing.stl | 537.7KB | |
| tail_wheel_mount.stl | 488.6KB | |
| ugly_stick_fuslage.zip | 37.8MB | |
| V-stab.stl | 5.1MB | |
| V-stab_r5.stl | 5.2MB | |
| V-stab_r5_repaired.stl | 5.2MB | |
| Wing.zip | 109.2MB | |
| wing_center.stl | 3.8MB | |
| wing_left_middle.stl | 5.8MB | |
| wing_right_middle.stl | 5.8MB | |
| Wing_saddle_front_cliip.stl | 168.3KB | |
| Wing_saddle_front_no_gear_slot.stl | 1002.5KB | |
| Wing_saddle_front_w_gear_slot.stl | 1.1MB |
![Mini Glider “KAWASEMI” [BFX16-UsNFY] 　ver.1.0 3D Printer Model](https://res.3axis.co/99de3e99-eae1-41cc-abdf-1ccda4476b50/images/89494253-93f9-414a-a304-a3a2ae31c144_thumb.jpg)
