Toyota 4 Cylinder Engine 22RE, Complete Working Model 3D Printer Model
The file 'Toyota 4 Cylinder Engine 22RE, Complete Working Model 3D Printer Model' is (STL,stl,pdf) file type, size is 36.1MB.
The file 'Toyota 4 Cylinder Engine 22RE, Complete Working Model 3D Printer Model' is (STL,stl,pdf) file type, size is 36.1MB.
Complete hardware kits that include all the non-printed parts can be found over at MakerRx
Complete hardware kits
Completely reverse engineered Toyota 22RE 4 cylinder engine. Can completely print a fully rotating model. Working crank, pistons, and valve train. The valves open and close!!!. It may not be the most exciting engine but its the only one I had in my garage. Great if you want to learn about engines and how the moving parts in them work. All parts are printed except for a few bearings and fasteners.
More than 3 days of total print time.
The block alone was 34 hours. So make sure you have a well calibrated and reliable printer.
Some print times calculated in Cura at .2mm layer height
Engine Block - 40 hours
Head - 23 hours
Valve Cover - 10 hours
Oil pan - 14 hours
| 22RE_Block_-_Cover.STL | 7.4MB | |
| 22RE_Block_-_Cutaway.stl | 10.2MB | |
| 22RE_Block_-_Cutaway_-_Cover.stl | 315.7KB | |
| 22RE_Instructions_09012020.pdf | 10.4MB | |
| Camshaft1.stl | 139.8KB | |
| Camshaft2.stl | 139.8KB | |
| Cam_bearing_cap.stl | 205.1KB | |
| Cam_Gear.stl | 591.0KB | |
| Connecting_rod.stl | 597.2KB | |
| Connecting_rod_cap.stl | 279.5KB | |
| Crankend.stl | 105.1KB | |
| Crankshaft_spacer_.stl | 43.7KB | |
| Crank_1.stl | 526.6KB | |
| Crank_2.stl | 534.3KB | |
| Crank_3.stl | 526.6KB | |
| Crank_gear.stl | 382.2KB | |
| Crank_pulley.stl | 1.2MB | |
| Crank_spacer.stl | 23.1KB | |
| Cylinder_Head.stl | 10.3MB | |
| Distributor_Base.stl | 323.5KB | |
| Distributor_boot.stl | 663.7KB | |
| Distributor__Cap.stl | 1.3MB | |
| Exhuast_valve.stl | 218.5KB | |
| Fan.stl | 1.7MB | |
| Fanspacer.stl | 16.9KB | |
| Fan_clutch.stl | 1.4MB | |
| Fan_pulley.stl | 1.1MB | |
| Flywheel.stl | 501.0KB | |
| Fuel_pump_block_off_plate.stl | 26.1KB | |
| Header.stl | 2.1MB | |
| Head_brace.stl | 3.5MB | |
| Intake_Manifold_Lower.stl | 3.6MB | |
| Intake_manifold_upper_-_part_1.stl | 2.7MB | |
| Intake_manifold_upper_-_part_2.stl | 1.4MB | |
| Intake_valve.stl | 220.5KB | |
| Left_motor_mount.stl | 178.5KB | |
| Main_cap.stl | 279.4KB | |
| Oil_cap.stl | 428.5KB | |
| Oil_pan.stl | 865.0KB | |
| Piston.stl | 1.8MB | |
| Rear_Main.stl | 2.3MB | |
| Right_motor_mount.stl | 189.0KB | |
| Rocker_arm.stl | 1.3MB | |
| Spark_plug_boot.stl | 241.4KB | |
| Spark_plug_wire_barrel_jack_cover.stl | 50.7KB | |
| Spring_retainer.stl | 53.5KB | |
| Starter_Drive_Gear.stl | 83.3KB | |
| Starter_Motor_Cover.stl | 47.4KB | |
| Starter_Motor_Mount.stl | 62.7KB | |
| Thermostat_housing.stl | 1.3MB | |
| Throttle_body.stl | 1.3MB | |
| Timing_cover.stl | 4.9MB | |
| Timing_Idle_gear_1.stl | 315.7KB | |
| Timing_Idle_gear_2.stl | 315.7KB | |
| Timing_Idle_gear_3.stl | 285.0KB | |
| VALVE_COVER.stl | 1.5MB |
