Tachikoma – Fully Articulated 3D Printer Model
The file 'Tachikoma – Fully Articulated 3D Printer Model' is (stl) file type, size is 13.0 MB.
The file 'Tachikoma – Fully Articulated 3D Printer Model' is (stl) file type, size is 13.0 MB.
Fully articulated version of Makerbog's "print by colour" Tachikoma model rebuilt in Fusion 360.
Features:
Full ball joints on elbows, Hips, Knees, Ankles, and gun
Movable, spherical eyes
Extendo arms
Hinged ankle for wheel transformation
Interchangeable toe/wheen segments
Optional gattling gun replacer with spinning barrels
All parts optimized for printing and seperated by colour - no painting required
Eye holes will fit a segment of 1.75 black filament
(Fairly advanced print with many small parts) (The model pictured is about 10% larger than the files, about the size of a football)
NOTE - Ball joints have 0.1mm clearance all around. This makes them a bit loose as this model is quite heavy, but any smaller makes them impossible to fit together.
The solution I use is to paint the backs of the sockets with 1 or 2 coats of Plasti dip (or similar liquid rubber), this gives them some resistance and should then happily support the models weight. (not required for gun socket or eyes)
| Ankle_Ball_x4.stl |
| Ankle_Hinge_Pin_x4.stl |
| Ankle_Shaft_x4.stl |
| Cabin_Back_Blue.stl |
| Cabin_Back_Insert_Lower_Black.stl |
| Cabin_Back_Insert_Upper_Black.stl |
| Cabin_Ball_Grey.stl |
| Cabin_Eye_Bottom_White.stl |
| Cabin_Front_Back_Peg.stl |
| Cabin_Front_Blue.stl |
| Cabin_Front_Insert_Bottom_Long_Black.stl |
| Cabin_Front_Insert_Bottom_Short_Black.stl |
| Cabin_Front_Insert_Left_Black.stl |
| Cabin_Front_Insert_Middle_Black.stl |
| Cabin_Front_Insert_Right_Black.stl |
| Cabin_Head_Connector.stl |
| Cabin_Insert_Spinnerette_Grey_x4.stl |
| Cabin_Light_Large_Red_x4.stl |
| Cabin_Light_Small_Red_x4.stl |
| Cabin_Turret_Grey_x2.stl |
| Cabin_Turret_Peg_x2.stl |
| Elbow_Grey_x2.stl |
| Foot_x4.stl |
| Head_Bottom_Blue.stl |
| Head_Bottom_Cap_Grey.stl |
| Head_Bottom_Cap_Peg.stl |
| Head_Eye_White_x3.stl |
| Head_Gattling_Gun_Ball_Grey.stl |
| Head_Gattling_Gun_Ball_Peg.stl |
| Head_Gattling_Gun_Barrels_Grey.stl |
| Head_Gattling_Gun_Body_Grey.stl |
| Head_Gattling_Gun_Muzzle_Grey.stl |
| Head_Gattling_Gun_Rear_Insert_Left_Grey.stl |
| Head_Gattling_Gun_Rear_Insert_Right_Grey.stl |
| Head_Hip_Socket_Grey_x4.stl |
| Head_Hip_Socket_Peg_x4.stl |
| Head_Insert_Black_x4.stl |
| Head_Insert_Dome_Grey.stl |
| Head_Insert_Plug_Grey.stl |
| Head_Insert_Screw_Grey_x2.stl |
| Head_Middle_Disk_Grey.stl |
| Head_Middle_Peg.stl |
| Head_TailJoint_Blue.stl |
| Head_Top_Blue.stl |
| Knee_Ball_Half_x8.stl |
| Knee_Ring_x4.stl |
| Left_Arm_Blue.stl |
| Left_Claw_Grey.stl |
| Left_Finger_Black_x3.stl |
| Left_Finger_Tip_Grey_x3.stl |
| Left_Wrist_Ring_Grey.stl |
| Left_Wrist_Rod_Grey_x2.stl |
| Left_Wrist_Shaft_Grey.stl |
| Leg_x4.stl |
| Mouth_Ball_Grey.stl |
| Mouth_Cannon_Grey.stl |
| Mouth_Cap_Grey.stl |
| Mouth_Key_Grey.stl |
| Mouth_Neck_Blue.stl |
| Mouth_Peg_x2.stl |
| Right_Arm_Blue.stl |
| Right_Claw_Grey.stl |
| Right_Wrist_Shaft_Grey.stl |
| Shin_Guard_x4.stl |
| Stand_mount_Optional.stl |
| Thigh_Cover_x4.stl |
| Thigh_x4.stl |
| Toe_x12.stl |
| Wheel_Section_x12.stl |
| Wrist_Guard_Grey_x2.stl |
