THESE FILES ARE PROVIDED FOR FREE ON A NON-COMMERCIAL LICENSE - PLEASE DO NOT SELL PRINTS OR COPIES OF THESE FILES

NOTE: I NO LONGER USE THINGIVERSE - FOR SUPPORT, PLEASE CONTACT ME VIA PRINTABLES: https://www.printables.com/social/242618-magnavis/about

Magnavis:

@Magnavis_
www.magnavis.co.uk

if you'd like to show some support for the 3D files I provide, you can 'buy me a coffee' here: https://ko-fi.com/magnavis_3d

UPDATE 2020

We have a new handle! After a long time of people asking, I have finally updated the handle, and all of the parts now connect to 8mm rod. No more flat end connections!

The handle fits 3 rods overall instead of the one, due to the slight curve the handle has.

Changes made:

• Re-skinned and fixed geometry for original handle file
• Adjusted sculpt and details
• Reduced curve in handle to be more accurate
• No more flat surfaces for connections - 8mm stud slots for all pieces!
• New connection pieces for handle parts 1 and 2. (Handle-001 + 002)
• Made the branch wraps a little thinner - should make them fit a little less snug.

With the new geometry, handle parts can now easily be cut in MeshMixer if you require smaller pieces.

Any questions, as always, please ask!

Thanks!

I have now completed my own print of Stormbreaker

Build Log: http://www.magnavis.co.uk/build-3d-printed-stormbreaker-avengers-infinity-war/

The file has now been test printed (Old handle - not new). From my testing, everything prints wonderfully (on a Wanhao i3 Plus - Using Cura)

All V2 Handle pieces are yet to be test printed (and wont be by me). But they all slice perfectly fine, so there shouldn't be any problems.

The complete pieces are as follows (You can seem them pictured above):

• Stormbreaker-Axe-head-001.stl
• Stormbreaker-Axe-Head-002.stl
• Stormbreaker-Axe-Head-003.stl
• Stormbreaker-Hammer-Head-001.stl
• Stormbreaker-Hammer-Head-002.stl
• Stormbreaker-Hammer-Head-003.stl
• Stormbreaker-Hammer-Head-004.stl
• Stormbreaker-Hammer-Head-005.stl
• Stormbreaker-Hammer-Head-Center-Block.stl
• Stormbreaker-Handle-V2-001.stl
• Stormbreaker-Handle-V2-002.stl
• Stormbreaker-Handle-V2-003.stl
• Stormbreaker-Handle-V2-004.stl
• Stormbreaker-Handle-V2-005.stl
• Stormbreaker-Handle-V2-006.stl

I have also added files named Rod 1, 2 and 3. These are NOT to be used to connect the pieces. But they are the correct sizes for the holes. You can either print them and use them to measure your 8mm rod, or you can just get the measurements from the 3D files - Up to you.

If you have any issues printing, please message me here, or shoot me a tweet. I'll be happy to help in anyway I can.

UPDATE 31/01/19 - Fixed an issue with Center Block piece. Not sure how it broke, but it should be ok now.

UPDATE 06/02/19 - Re-Uploaded the central block. Handle - Head connection hole for rod was accidentally removed. This has now been re-added.

UPDATE 26/03/2019 - Re-added the larger handle parts. This allows the handle to be printed in 6 pieces instead of 10, if you have the printer height.

UPDATE 19/06/2019 - Stormbreaker-Handle-002-A & Stormbreaker-Handle-002-B + Stormbreaker-Handle-001-A and Stormbreaker-Handle-001-B files added. This is the the parts sliced in two, down the middle to try and combat an issue a user was having with not enough RAM (oops!)

UPDATE 11/06/2020 - Revised thing details, and added new handle files. See Above.