Update-2022-03-04: After the surprising success of version 2 of these baskets (full baskets, all sides with honeycombs), I decided to create a compromise between the two and called it "version 1b". The main difference to v1 is the angled front, which now has honeycombs (like v2), but I kept the closed bottom, so that nothing can fall through. And with the right Slicer settings they do not even need more filament than version 2. (see below)
Yet another set of stackable containers. You can find several different sets of stackable boxes on thingiverse, but many of them are for very small things only or use quite a bit of filament, so the DIY variant isn't much cheaper than buying some boxes.
Therefore I was looking for a compromise between size, stackability and minimal use of filament - stackable baskets of reasonable size. The largest one (30cm x 10cm) need only 100g of filament and of course no support. An due to the honeycomb structure and some stiffeners they are still stable enough.
I decided for 10cm wide and 7.5cm high boxes with different length, up to 30cm, which would just fit straight on a 30x30 cm print bed*). All sizes are stackable on each other. You can also stick a paper label to the front.
Remark: I have also created a remix with "full baskets", i.e. honeycombs also on bottom: thing:5156678
| StackableBasket-10x10.stl | 253.1KB | |
| StackableBasket-11x10.stl | 271.3KB | |
| StackableBasket-12x10.stl | 290.5KB | |
| StackableBasket-13x10.stl | 308.6KB | |
| StackableBasket-14x10.stl | 323.1KB | |
| StackableBasket-15x10.stl | 336.1KB | |
| StackableBasket-16x10.stl | 357.9KB | |
| StackableBasket-17x10.stl | 374.4KB | |
| StackableBasket-18x10.stl | 389.4KB | |
| StackableBasket-19x10.stl | 405.3KB | |
| StackableBasket-20x10.stl | 431.2KB | |
| StackableBasket-21x10.stl | 443.3KB | |
| StackableBasket-22x10.stl | 457.9KB | |
| StackableBasket-23x10.stl | 473.0KB | |
| StackableBasket-24x10.stl | 498.9KB | |
| StackableBasket-25x10.stl | 511.2KB | |
| StackableBasket-26x10.stl | 526.1KB | |
| StackableBasket-27x10.stl | 542.5KB | |
| StackableBasket-28x10.stl | 563.1KB | |
| StackableBasket-29x10.stl | 583.5KB | |
| StackableBasket-30x10.stl | 593.4KB | |
| V1b-StackBasket-10x10.stl | 315.3KB | |
| V1b-StackBasket-11x10.stl | 331.6KB | |
| V1b-StackBasket-12x10.stl | 364.6KB | |
| V1b-StackBasket-13x10.stl | 380.9KB | |
| V1b-StackBasket-14x10.stl | 391.7KB | |
| V1b-StackBasket-15x10.stl | 407.2KB | |
| V1b-StackBasket-16x10.stl | 439.6KB | |
| V1b-StackBasket-17x10.stl | 455.0KB | |
| V1b-StackBasket-180x10.stl | 467.8KB | |
| V1b-StackBasket-19x10.stl | 486.0KB | |
| V1b-StackBasket-20x10.stl | 515.4KB | |
| V1b-StackBasket-21x10.stl | 533.4KB | |
| V1b-StackBasket-22x10.stl | 541.5KB | |
| V1b-StackBasket-23x10.stl | 558.2KB | |
| V1b-StackBasket-24x10.stl | 595.1KB | |
| V1b-StackBasket-25x10.stl | 605.6KB | |
| V1b-StackBasket-26x10.stl | 621.3KB | |
| V1b-StackBasket-27x10.stl | 634.0KB | |
| V1b-StackBasket-28x10.stl | 664.5KB | |
| V1b-StackBasket-29x10.stl | 685.1KB | |
| V1b-StackBasket-30x10.stl | 693.7KB |
