Sea Ghost V3, Galleon Conversion 3D Printer Model
The file 'Sea Ghost V3, Galleon Conversion 3D Printer Model' is (stl) file type, size is 3.6MB.
The file 'Sea Ghost V3, Galleon Conversion 3D Printer Model' is (stl) file type, size is 3.6MB.
After a bit of poking around with the Sea-Ghost RPG sailing ship for a remix request, i decided to re-remix it to how I wanted it to be set up for game play.
There is now 4 or 5 different options (at the time of this initial upload) for this rather nifty sailing vessel model by a few different individuals here. If you print this, please upload a photo. If you run into errors message me and i'll see about fixing it.
This edit/remix of the Sea Ghost was done entirely in Blender3d using the base files for the Sailing Ship. The masts are available from the original item file, Shown under sources.
The Mermaid figurehead is also posted separately as its own item. http://www.thingiverse.com/thing:1430885
My thought is to bond all three bases together making a tray. the upper decks have a grooved edge to allow them to sit tightly onto the tray base. The entire upper structure is able to come off in pieces to allow a variety of levels of access during game play.
There is a piece in here as a mast support that will need to be bonded to the lower center section.
Edit: Error on My part. Fixed the issue, re-exported and reuploaded all files.
I am sorry for any inconvenience this has caused, and thank you for pointing it out.
Edit2: added generic_hatch Frame and Hatch Cover so that any part of the inner deck can be cut out and turned into an access panel. Generic hatch frame has been made to a slightly greater thickness of the stern deck panel. Hatch just sits in the frame, hinges if wanted will have to be a DIY item. A ladder would be the access item to the under deck.
Edit3: Increased Deck thicknesses, as well as depth of the Generic hatch cover, its frame, and the Hatch for the cargo hold in the center section.
Bow_Base_2 and Bow_Cabin_2 are not interchangle with the original, both are left on here. The revision 2 has the join of the bowsprit section meeting at the lower intersection of the joint groove. The original is at the upper intersection of the joint groove. If you are printing the original support will be needed, although you might want it anyway on the upper sections for the joint groove. See the comment section.
Stern_Cabin_2 had its inner deck support lip lowered to match the new thickness of that deck.
edit 4: Bow Base "repaired" has been ran through netfabb to fix a slicing issue that shows up in Cura which sliced the model part as a solid object. both files are going to be left up so check which one your attempting to print.
| Bow_Base.stl | 82.9KB | |
| Bow_Base_2.stl | 82.9KB | |
| Bow_Base_2_repaired.stl | 93.0KB | |
| Bow_Cabin.stl | 152.5KB | |
| Bow_Cabin_2.stl | 154.2KB | |
| Bow_Cabin_InnerDeckPlate.stl | 29.6KB | |
| Bow_Cabin_TopDeckPlate.stl | 44.0KB | |
| Bow_Cabin_Wall.stl | 36.9KB | |
| Bow_DeckPlate_Lower_3.stl | 29.6KB | |
| Bow_DeckPlate_Upper_3.stl | 44.0KB | |
| Center_Base.stl | 44.4KB | |
| Center_DeckPlate_3.stl | 41.8KB | |
| Center_Deck_Plate.stl | 41.8KB | |
| Center_Top.stl | 13.6KB | |
| Deck_Hatch.stl | 44.1KB | |
| Deck_hatch_3.stl | 44.1KB | |
| figurehead.stl | 3.8MB | |
| Generic_Hatch_Cover_3.stl | 6.5KB | |
| Generic_Hatch_Frame_3.stl | 2.8KB | |
| Mast_Crows_Nest.stl | 107.2KB | |
| Mast_Step2.stl | 27.8KB | |
| Stern_Base.stl | 22.8KB | |
| Stern_Cabin.stl | 185.0KB | |
| Stern_Cabin_2-hopefully_fixed3.stl | 185.1KB | |
| Stern_Cabin_2.stl | 184.8KB | |
| Stern_Cabin_InnerDeckPlate.stl | 50.3KB | |
| Stern_Cabin_TopDeckPlate.stl | 39.5KB | |
| Stern_Cabin_Wall.stl | 41.4KB | |
| Stern_DeckPlate_Lower_3.stl | 50.3KB | |
| Stern_DeckPlate_Upper_3.stl | 39.5KB | |
| Stern_TillerPost.stl | 50.5KB |
