Based on This ROV youtube. com/watch?v=TfJ0Y3oZTzQ (get rid of the space)
Plumbing Parts List
8 - 3/4 inch Elbows
10 - 3/4 inch Tees
4 - two inch caps
4 - one inch caps
2 ft one inch pipe
8 ft 3/4 inch pipe (I bought four 2 ft pieces)
1 - 4 inch closed box (see below)
4 - 1/2 x 2” PVC pipe
3D Print List
1) ROV_VERT_MT_RING_v2.stl
4) ROV_4x4_Box_MT_v2.stl
4) ROV_Ballast_v2.stl
1) ROV_Cabinet_Grommet_v3.stl
1) ROV_Cable_Support_v3.stl
1) ROV_CAM_MT_v10.stl
1) ROV_Control_Box_Bottom_v1.stl
1) ROV_CTRL_PANEL_2_v2.stl
1) ROV_CTRL_PANEL_v9.stl
2) ROV_CTRL_PNL_BRACE_v2.stl
4) ROV_Floats_v2.stl
2) ROV_HORZ_MOT_MT1_v2.stl
2) ROV_HORZ_MOT_MT2_v7.stl
2) ROV_Motor_Cowling_v2.stl
1) ROV_Tether_Knot_Cover_v2.stl
1) ROV_VERT_MOT_MT_v3.stl
Speaker Wire 14 Gauge AWG 100ft Speaker Wire Cable - Red/Black
https://www.amazon.com/gp/product/B078YYLT5T/ref=ppx_yo_dt_b_asin_title_o05__o00_s00?ie=UTF8&psc=1
Cat5 Wire
Cat5e 100FT Networking RJ45 Ethernet Patch Cable Xbox PC Modem PS4 Router - (100 Feet) Blue
https://www.amazon.com/gp/product/B01CI9MEYU/ref=ppx_yo_dt_b_asin_title_o05__o00_s00?ie=UTF8&psc=1
4 -Bilge Pumps
12v 1100gph Boat Marine Plumbing Electric Pump Unique for Any Blige-amarine-made
https://www.ebay.com/p/12v-1100gph-Boat-Marine-Plumbing-Electric-Pump-Unique-for-Any-Blige-amarine-made/5012102393?iid=201952409317&chn=ps
Use a Dremel to cut away the pump housing on all four pumps. Cut just a bit after the red plastic ends and the white starts.
Props
2 Sets D45mm 3-Blades Left/Right P1.7 RC Boat Propellers 4mm Shaft US SELLER/SHIP
https://www.ebay.com/itm/1Set-D45mm-3-Blades-Left-Right-P1-7-RC-Boat-Propellers-4mm-Shaft-US-SELLER-SHIP/172020667309?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649
I found some thin plastic tubing that worked a shim and press fit into the props, then epoxied them on to the pump shafts after filling the pump shaft recess with grease and covering it with a thin plastic disc.
8 - Relays (4 packs of two)
OEG OMI-SS-212L DPDT 12VDC Coil PC Mount Relay 5A @ 250VAC/28VDC Contacts 2 pcs
https://www.ebay.com/itm/OEG-OMI-SS-212L-DPDT-12VDC-Coil-PC-Mount-Relay-5A-250VAC-28VDC-Contacts-2-pcs/223001317486?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649
1 - 4x4 Electronics Junction Box with gasket seal
https://www.homedepot.com/p/Carlon-4-in-x-4-in-x-2-in-PVC-Junction-Box-E989NNJ-CAR/100404097
I filled the electronics box with 90 weight gear oil then capped it with melted parafin. Then added a little silicon sealant to the gasketed lid and installed it.
1 - Fishing Camera
https://www.amazon.com/gp/product/B07513DXRZ/ref=ppx_yo_dt_b_asin_title_o00__o00_s00?ie=UTF8&psc=1
4 - Control Switches
https://www.amazon.com/gp/product/B01FA9UNMA/ref=ppx_yo_dt_b_asin_title_o02__o00_s00?ie=UTF8&psc=1
1 - On/Off Switch
https://www.amazon.com/gp/product/B07D2CX76S/ref=ppx_yo_dt_b_asin_title_o02__o00_s00?ie=UTF8&psc=1
1 - On/Off Switch Connector
https://www.amazon.com/gp/product/B01H5BMXKG/ref=ppx_yo_dt_b_asin_title_o00__o00_s00?ie=UTF8&psc=1
100 ft Tether Cord
https://www.amazon.com/gp/product/B07FS9LDLM/ref=ppx_yo_dt_b_asin_title_o02__o00_s00?ie=UTF8&psc=1
100 ft Spiral Tether Wrap: https://www.amazon.com/gp/product/B07CH2DSM7/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1
I cut this stuff into 10 foot lengths and covered the junctions with 1 foot lengths of 1/2 inch pipe insulation. I don't yet know if the floatation is too little, too much or just right...
1 - Compass
https://www.amazon.com/gp/product/B000LC844Q/ref=ppx_yo_dt_b_asin_title_o01__o00_s00?ie=UTF8&psc=1
Circuit Board -I can make you these relay boards (holds 8 relays) for $50 each.
If you want to make your own I've included the artwork in negative for use with the dry film photo resist process. This board would need two jumpers on the two pairs of relay/motor outputs that are end to end (+ to - and - to +) >> only one can be 'on' at a time.
Gripper (previously posted)
https://www.thingiverse.com/thing:3447594
I'm happy to answer any questions about the construction and or upload more detail pics.
See a video from the ROV in action. In this video the claw is folded back under the ROV so it is in Camera Only Mode: https://youtu.be/eNyRvkDXL-M
In this video I use the claw to retrieve from the bottom. The last part of the retrieve is done via the cable/ 400lb test tether. https://youtu.be/YdAvQyoZjMA
| ROV_4x4_Box_MT_v2.stl | 213.9KB | |
| ROV_Ballast_v2.stl | 60.0KB | |
| ROV_Cabinet_Grommet_v3.stl | 433.0KB | |
| ROV_Cable_Support_v3.stl | 231.1KB | |
| ROV_CAM_MT_v10.stl | 167.5KB | |
| ROV_Control_Box_Bottom_v1.stl | 48.3KB | |
| ROV_CTRL_PANEL_2_v2.stl | 12.4KB | |
| ROV_CTRL_PANEL_v9.stl | 14.9KB | |
| ROV_CTRL_PNL_BRACE_v2.stl | 1.3KB | |
| ROV_Floats_v2.stl | 57.3KB | |
| ROV_HORZ_MOT_MT1_v2.stl | 45.0KB | |
| ROV_HORZ_MOT_MT2_v7.stl | 160.1KB | |
| ROV_Motor_Cowling_v2.stl | 248.8KB | |
| ROV_Tether_Knot_Cover_v2.stl | 348.2KB | |
| ROV_VERT_MOT_MT_v3.stl | 180.5KB | |
| ROV_VERT_MT_RING_v2.stl | 151.7KB |
