Refil 3D Mini Beast 3D Printer Model
The file 'Refil 3D Mini Beast 3D Printer Model' is (stl,zip) file type, size is 7.0MB.
The file 'Refil 3D Mini Beast 3D Printer Model' is (stl,zip) file type, size is 7.0MB.
You can find the improved V2 of this printer here https://www.thingiverse.com/thing:3863140
A corexy printer designed with ease of assembly, use and maintenance in mind. All rods on the build can be easily removed without removing any of the parts that hold them from the frame.
I am continuously updating the parts lists below and the models of the parts as I try new parts and improve the existing ones.
The printer build uses 2020 extrusions to keep the cost of low, while building a solid printer.
The current plan is for a 300x300x300mm build volume. You could use any parts you want to adjust the volume, however any bigger than 400x400x400 is not advised due to the parts designed for 2020 extrusions.
Using 2020 extrusions is a requirement, otherwise the parts will not fit!!
A list of all the parts needed to complete the build will be provided shortly after the full build is ready and tested.
Plastic Parts to print:
2 x Z Motor Mounts
8 x Z Rod Holders (pick the right version for 8mm or 10mm rods)
1 x Left Y Motor Mount (V2 part)
1 x Right Y Motor Mount (V2 part)
1 x Left Y Rod Mount (V2 part)
1 x Right Y Rod Mount (V2 part)
8 x Bearing Standoffs
1 x Endstop Clicker
1 x Endstop Mount for Y-axis
2 x Bed Mounts(set)
List of Parts you need:
Parts for the 300 model (300mmx300mmx300mm):
2 x 450mm 2040 extrusions
6 x 450mm 2020 extrusions
4 x 500mm 2020 extrusions
4 x 300mm 2020 extrusions (for mounting the bed)
Total I paid for extrusions is £115 but you can find them cheaper ~£60, especially if you can cut them to length yourself (mine were cut to length and anodized black)
2 x 10mm 450mm smooth rods £25.30
2 x 10mm 430mm smooth rods £24.20
4 x 8mm 400mm smooth rods for Z axis £31.60
4 x LMH8LUU 8mm Linear Bearing for Z Axis £22
2 x 8mm Lead Screw 370mm for Z axis £15
12V 280W 300*300mm Flexible Silicone Heating bed £18
PSU £30
Parts for the 400 model (400mmx400mmx400mm):
For the 400 model, just add 100mm to all of the extrusions, rods and the lead screws.
Parts for both versions:
5M GT2 Belt and 2 Pulleys £14.50
8 x Igus Drylin LM10UU Bearings (you can use regular 10mm bearings but these are quiet) £15
1 x Arduino 2560 £6
1 x RAMPS 1.4 £6
5 x DRV8825 Stepper Drivers £5.10
5 x NEMA 17 Motors (2 driving the bed can be long ones with higher torque) £40
1 x E3D v6 Full Metal (Can be either bowden or direct, 1.75mm/3mm, your choice) £52
1 x E3D Titan Extruder (Need 2 for dual colour and an extra NEMA 17!) £59
10 x F623ZZ Flange Ball Bearing Shielded 3 X 10 X 4mm £18
Facebook Group: https://www.facebook.com/groups/641612192699533/
| 90d-angles.stl | 972.8KB | |
| angles-v2.stl | 481.7KB | |
| bearing-standoff.stl | 102.0KB | |
| bed-adjuster-mount.stl | 445.2KB | |
| hotend-carriage-V2.stl | 1.6MB | |
| hotend-holder-bowden.stl | 461.4KB | |
| hotend-mount-secure-side.stl | 120.3KB | |
| left-y-motor-mount-v2.stl | 2.4MB | |
| left-y-rod-holder-v2.stl | 1.6MB | |
| legs.stl | 192.0KB | |
| Marlin-mBeast.zip | 2.9MB | |
| right-y-motor-mount-v2.stl | 2.4MB | |
| right-y-rod-holder-v2.stl | 1.6MB | |
| X-axis-limit-clicker.stl | 50.0KB | |
| X-rod-caps-V2.stl | 126.4KB | |
| Y-carriage.stl | 981.6KB | |
| y-endstop-holder.stl | 141.7KB | |
| Y-rod-cap.stl | 457.2KB | |
| z-bearing-holder-8mm-bearing.stl | 597.6KB | |
| Z-brass-nut-holder-10mm-screw.stl | 2.1MB | |
| Z-brass-nut-mount-8mm.stl | 554.8KB | |
| Z-lead-screw-support-10mm.stl | 432.7KB | |
| Z-lead-screw-support.stl | 463.0KB | |
| Z-linear-bearing-holder-LMH10L.stl | 598.8KB | |
| Z-motor-mount.stl | 908.6KB | |
| Z-rod-holder-10mm.stl | 494.3KB | |
| Z-rod-holder-8mm.stl | 521.4KB |
