The file 'Rc Fpv Plane Made In Fluted Plastic Sheets . Fiberglass Stick . 3D Print Parts ( Modular ) . Simple . Easy DIY 3D Printer Model' is (stl) file type, size is 519.2KB.
Please Like, Post a make, Comment, Give me a tip
with the tip system of thingiverse
https://www.thingiverse.com/Kaaa/about
/////////////////////////////
update 05/01/2019:
video 3: crazy proximity acrobatic test flight & crash
/////////////////////////////
update 04/09/2019:
<<<< video: how to make the wing >>>> ( quick build )
https://dai.ly/x75j6b4
/////////////////////////////
cheap and hard to break ;-) except the
"p2_p-pane_project_head_bat_and_cam_mount_v1.***.stl"
is planned for breaking in case of crash for save the cam
hardware:
9gr servos X3
5/50X3 propeller ( 6 inch compatible )
1300mah 3s lipo or 1300mah 3s X2 in parallel
30a esc
Racerstar BR2212 2450KV
plane made in ~3-4mm Fluted plastic sheets ( the Fluted plastic sheets are a recovery on a trash pallet )
4mm diameter ~50cm length fiberglass stick X4 ( Kite parts,i think the diameter is a little to small (stronger is better), you can add a stick in the wing for reinforce )
3d print parts
hot glue and adhesive tape
i advise you to make some cuts to the first layer inside the fluted plastic sheet to facilitate folding against the wing structure ( quick build video for more details https://dai.ly/x75j6b4 )
//////////////////////////////////////////////////////////////////////////video1
(modularity and acrobatic speed flight test)
Parts use in the video 1 and the picture 2:
motor mount push fV
p1 p-pane project end
( I advise you to use the "p1 p-pane project super shorter V2" and its "extensions" easier for balanced the airplane )
p2 p-pane project head bat and cam mount v1.1
p-pane project wing X7
////////////////////////////////////////////////////////////////////////video2
(low speed, stalling, gliding and aerodynamic turbulence test)
Parts use in the video 2 :
motor mount push fV
p1 p-pane project super shorter V2
p1-p2_extension_2.stl
p2 p-pane project head bat and cam mount v1.2
p-pane project wing X7
runcam 3
aomway hb25t camera-tx combinate combine (housing: https://www.thingiverse.com/thing:3514717 )
one 13000mha 3s lipo
//////////////////////////////////////////////////////////////////////////video3
(crazy proximity acrobatic test flight & crash)
Parts use in the video 3 :
motor mount push fV
p1 p-pane project super shorter V2
p1-p2_extension_2.stl
p2 p-pane project head bat and cam mount v1.2
p-pane project wing X7
runcam 3
aomway hb25t camera-tx combinate combine (housing: https://www.thingiverse.com/thing:3514717 )
2 1300mah 3s liopo in parallel
///////////////////////////////////////
Flight time duration :
5.30min with 1 1300mah 3s liopo in mix flight acrobatic full throttle and gliding motor off. Without camera
11min with 2 1300mah 3s liopo in parallel, mostly at 60-70% motor throttle. 1 combinate tx camera( picture "set up 2" )
5 min with 1 1300mah 3s liopo. 1 combinate camera-tx + runcam 3 (video 2)
6 min with 2 1300mah 3s liopo in parallel,mostly at 80-100% motor throttle 1 combinate tx camera + runcam3
have a nice flight
| motor_mount_push_fV.stl | 38.6KB | |
| p-pane_project_motor_mount_pull_Fv.stl | 176.7KB | |
| p-pane_project_wing.stl | 145.8KB | |
| p1-p2_extension.stl | 23.0KB | |
| p1-p2_extension_2.stl | 23.1KB | |
| p1-p2_extension_3.stl | 28.1KB | |
| p1_p-pane_project_end.stl | 185.1KB | |
| p1_p-pane_project_end_shorter_V.stl | 167.2KB | |
| p1_p-pane_project_end_shorter_V2.stl | 151.1KB | |
| p1_p-pane_project_end_super_shorter_V2.stl | 226.7KB | |
| p1_p-pane_project_end_v2.stl | 152.8KB | |
| p2_p-pane_project_head_bat_and_cam_mount_v1.1.stl | 41.4KB | |
| p2_p-pane_project_head_bat_and_cam_mount_v1.2.stl | 43.5KB | |
| p2_p-pane_project_head_bat_and_cam_mount_v1.3.stl | 47.5KB | |
| p2_p-pane_project_head_bat_and_cam_mount_v1.4.stl | 40.4KB | |
| p2_p-pane_project_head_bat_and_cam_mount_v1.5.1.stl | 134.1KB | |
| p2_p-pane_project_head_bat_and_cam_mount_v1.5.stl | 130.8KB | |
| p2_p-pane_project_head_bat_and_cam_mount_v1.6.stl | 41.9KB | |
| p2_p-pane_project_head_bat_and_cam_mount_v1.7.stl | 57.4KB |
