Primbal Session – 3 Axis Brushless Gimbal For GoPro Session 3D Printer Model
The file 'Primbal Session – 3 Axis Brushless Gimbal For GoPro Session 3D Printer Model' is (stl) file type, size is 434.9KB.
The file 'Primbal Session – 3 Axis Brushless Gimbal For GoPro Session 3D Printer Model' is (stl) file type, size is 434.9KB.
*This latest design has not been physically tested
Primbal Session. Finally a gimbal that supports that GoPro Session of yours. This gimbal is based on the Primbal V3 design for the Xiaomi Yi and GoPro 3/4 models.
Primbal V3 implements stronger, stiffer arms that make the gimbal more resistant to vibrations. Additionally, there are now four different isolator options to suite your fancy. The result is a more robust, versatile gimbal to bring you silky smooth video.
This gimbal is composed of 12 printed parts that are all printer friendly. All STLs are in the proper printing position, no reorienting required. All three axis (pitch, roll, yaw) are fully adjustable to perfectly balance the gimbal. This gimbal is designed to best perform with the GoPro Hero and Hero5 Session.
Parts:
12 Printed
Hardware:
8 x M2 Bolt 8mm
2 x M2 Nut
4 x M3 Bolt 4mm
2 x M3 Bolt 6mm
Motors:
2804 size for yaw (35mm diameter)
2206/2804 size for roll
2206 size for pitch (28mm diameter)
Confirmed to Fit:
Hobbyking 2804-210Kv
Hobbyking 2206-140Kv
Rctimer GBM2804
Might Fit:
Quanum 2208
DYS BGM2208
Controller:
Any 3 axis brushless gimbal controller to externally control the gimbal. I recommend a Storm32 board.
Weight:
Approximately 250g with camera, 175g without
Range of Motion
Pitch: -90 +90
Roll: -45 +45
Yaw: Depends on wiring
Balancing on the roll and yaw axes is done through loosening the bolts holding the arms to the roll/yaw motors and sliding the bolt spacer along the adjustment slot. For the pitch axis a similar thing is done with the pitch adjuster to adjust up and down. To adjust the pitch axis back and forth, shift the Session forward or back before tightening down the camera bar.
If you need the design modified to fit a different gimbal motor or part, then let me know! I can modify the design for your needs. No guarantees though as there is only so much you can do without the physical parts in hand.
| BoltSpacerPrint2.stl | 20.2KB | |
| CameraBarSession.stl | 28.0KB | |
| IsolatorEightBallLower.stl | 201.6KB | |
| IsolatorEightBallUpper.stl | 244.1KB | |
| IsolatorFourBall7mmLower.stl | 135.8KB | |
| IsolatorFourBall7mmUpper.stl | 171.5KB | |
| IsolatorFourBall9mmLower.stl | 160.6KB | |
| IsolatorFourBall9mmUpper.stl | 203.8KB | |
| IsolatorWireRopeLower.stl | 106.3KB | |
| IsolatorWireRopeUpper.stl | 139.1KB | |
| PitchAdapterSession.stl | 35.4KB | |
| RollArm.stl | 107.7KB | |
| TubeHook1of2Print2.stl | 89.2KB | |
| TubeHook2of2Print2.stl | 89.4KB | |
| YawArm2206.stl | 101.3KB | |
| YawArm2804.stl | 119.9KB |
