Pendulum Clock 3D Printer Model
The file 'Pendulum Clock 3D Printer Model' is (stl,pdf) file type, size is 3.8MB.
The file 'Pendulum Clock 3D Printer Model' is (stl,pdf) file type, size is 3.8MB.
I've always been fascinated by clocks. Having a 3D printer gave me the opportuntiy to toy around with clock design and even learn a bit. This clock is the result of dissecting many different designs done by other (more knowledable) people,
This clock has a runtime of 16-18 hours before rewinding. I'm pretty sure I could double that with a change in the weight gear. Something to do in the future.
I included assembly instructions in a pdf document.
UPDATE 10/30/2020
After 8 months of operation, I realize that the original method of attaching the pendulum (with a two piece 'slip fit' fork) was not a very good idea. Over time, the 'slip-fit' became a 'too-loose-fit' causing the beat of the escapement (the tick-tock) to be inconsistant and difficult (or impossible) to adjust. I've replaced the two piece design with a one piece solid part (file '11A-Pendulum_Fork_Solid.stl') and updated the assembly PDF (see page 29). Working much better now.
| 10_Clock_Face.stl | 83.4KB | |
| 10_Clock_Numerals.stl | 102.0KB | |
| 11A-Pendulum_Fork_Solid.stl | 46.1KB | |
| 11_Pendulum_Axle.stl | 13.8KB | |
| 11_Pendulum_Bob_Connector.stl | 1.4KB | |
| 11_Pendulum_Fork.stl | 52.1KB | |
| 11_Pendulum_Section.stl | 2.4KB | |
| 11_Pendulum_Top_Hook.stl | 2.6KB | |
| 12_Weight_Body.stl | 73.9KB | |
| 12_Weight_Top.stl | 24.1KB | |
| Anchor_Pallet.stl | 16.8KB | |
| Assembly_Notes_rev2.pdf | 1.6MB | |
| Bob_Body.stl | 136.6KB | |
| Bob_Cover.stl | 13.2KB | |
| Escapement_Gear.stl | 856.5KB | |
| Frame_Back_LH.stl | 76.1KB | |
| Frame_Back_RH.stl | 98.9KB | |
| Frame_Front_LH.stl | 71.5KB | |
| Frame_Front_RH.stl | 98.6KB | |
| Gage5x11.stl | 42.5KB | |
| Gage5x15.5.stl | 81.5KB | |
| Gage5x19.stl | 65.5KB | |
| Gage5x5.5.stl | 76.3KB | |
| Gage6x11.stl | 54.4KB | |
| Gage6x19.stl | 77.4KB | |
| Gage6x21.stl | 63.2KB | |
| Gage6x23.stl | 82.5KB | |
| Gage6x32.stl | 82.5KB | |
| Gage6x34.5.stl | 102.6KB | |
| Gage6x5.5.stl | 88.2KB | |
| Gear_118mm_60T.stl | 478.1KB | |
| Gear_135mm_60T.stl | 480.7KB | |
| Gear_56mm_30T.stl | 366.3KB | |
| Gear_57mm_32T.stl | 423.3KB | |
| Gear_59mm_24T.stl | 225.5KB | |
| Gear_90mm_60T.stl | 435.9KB | |
| Gear_Pinion_Supports.stl | 230.1KB | |
| Gear_Supports.stl | 20.6KB | |
| Hour_Hand.stl | 38.1KB | |
| Minute_Hand.stl | 47.2KB | |
| Minute_Hand_Axle.stl | 38.8KB | |
| Pinion_16mm_8T.stl | 70.6KB | |
| Pinion_21mm_10T.stl | 60.0KB | |
| Pinion_26mm_16T.stl | 77.1KB | |
| Pinion_32mm_15T.stl | 80.0KB | |
| Pinion_36mm_15T.stl | 90.4KB | |
| Ratchet_Drum_Stop_Pins.stl | 147.7KB | |
| Ratchet_Drum_Stop_Plate.stl | 966.1KB | |
| Ratchet_Drum_Toothed.stl | 100.2KB | |
| Ratchet_Drum_Top.stl | 25.1KB | |
| Ratchet_Gear_48T.stl | 163.0KB | |
| Ratchet_Weight_Drum.stl | 63.2KB | |
| Shafts_5mm.stl | 2.0KB | |
| Shafts_6mm.stl | 4.0KB | |
| Shaft_18x5mm.stl | 12.4KB | |
| Shaft_EndStops_5mm.stl | 154.8KB | |
| Shaft_EndStops_6mm.stl | 309.5KB | |
| Shaft_Helper_Disc.stl | 3.8KB |
