01/09/2021 update: added a few more magazine holders.

03/29/2020 update: Added Glock 2-magazine holder, Beretta 81 holder, BX-25 holder, and a STANAG pattern AR-15 magazine holder.

The purpose of this project was to design a series of models which could be used to hang standard capacity magazines on a mounted piece of pegboard, for both ease of access, clear organization, and safe storage. This project went through several iterations before a final design was selected. Earlier revisions used less space, but did not have the strength necessary to support multiple magazines for extended period of time. This version results in more than one magazine being mounted per inch (distance between two pegboard holes) in most instances, and features resized arms in order to allow mounts to sit reasonably flush next to each other in the event that multiple holders are needed (as they should be). Magazines included in this posting have been successfully used to hang unloaded (and, for some mounts noted below, fully loaded) magazines for over four months with no detectable degradation.

There were no existing models for pegboard magazine holders which I was able to locate; this project drew inspiration from several existing models, most notably this AR-15 PMAG Holder by Mikeyman64 and this Pegboard Pliers Holder by HunterGreen.

Other than the 1911 magazine holder, these magazine holders are designed to have minimal bend to allow magazines to be seated, and to snap back into place once the magazines are inserted.

The following is a list of magazines holders which are included in this collection, including the magazine the model was designed for, other standard capacity magazines which I have confirmed to fit the listed model, and the number of magazines which that specific model will hold. Please note that unless specifically noted, these magazines have not been tested to hold fully loaded magazines.

• magHolder2 1911 (2): This is designed for 1911 magazines. No other magazines tested. It will hold two magazines.
• magHolder2 AK (1): This is designed for AK-47 Magpul PMAGs. It will also hold Tapco Ruger Mini 14 magazines. It will hold one magazine.
• magHolder2 AK (2): This is designed for AK-47 Magpul PMAGs. It will also hold Tapco Ruger Mini 14 magazines. It will hold two magazine.
• magHolder2 AR (2): This is designed for AR-15 Magpul PMAGs. It will also hold J&E 10 round AR-15 magazines. It will hold two magazines.
• magHolder2 AR (3): This is designed for AR-15 Magpul PMAGs. It will also hold J&E 10 round AR-15 magazines. It will hold three magazines.
• magHolder2 AR-alum (3): This is designed for AR-15 aluminum magazines, but should work on any STANAG mag. It will hold three magazines.
• magHolder2 Beretta 81 (3): This is designed for Beretta 81 magazines. It will hold three magazines.
• magHolder2 Bersa (2): This is designed for Bersa Thunder 380 magazines. It will also hold Ruger LCP-II magazines. It will hold two fully loaded magazines.
• magHolder2 BX-25 (2): This is designed for Ruger BX-25 magazines. It will hold two magazines.
• magHolder2 Glock (3): This is designed for Glock-pattern magazines. This is perhaps the most versitable mount, as it has also been used to mount Berrata 92fs Magazines, Menendez 3D Printable Glock Magazines, and Canik tp9 / tp9sf elite magazines. It will hold three fully loaded magazines.
• magHolder2 Glock (2): Same as the above Glock model, but this version holds two magazines.
• magHolder2 HPC (3): This is designed for OEM magazines Hi-Point Carbine (HPC) magazines. It will also hold (loosely) redball HPC magazines. It will three magazines.
• magHolder2 LRSR (2): This is designed for AR-10 Magpul LR/SR PMAGs. No other magazines tested. It will hold two magazines.
• magHolder2 LRSR (2) - too big: This is included for posterity sake. This was modelled for the Magpul LR/SR .308 AR-10 magazines, but the measurements are off. If you have a magazine slightly larger than the LR/SR, this might work for it.
• magHolder2 M14 (2): This is designed for OEM Ruger Mini 14 magazines. It is unlikely to hold any other magazines. It will hold two magazines.
• magHolder2 Shield (2): This is designed for M&P Shield (version one or two) magazines. No other magazines tested. It will hold two magazines.
• magHolder2 Shield (3): This is designed for M&P Shield (version one or two) magazines. It will also hold (loosely) two M&P 22 Compact magazines. It will hold three magazines.

It is of note that many other magazines will likely work in one of the above magazine holders; I have listed only the magazines which I have personally tested. If you would like me to design a magazine holder for a specific magazine not included above, feel free to contact me to discuss.