Since I want to give my nephew something very special for Christmas, I thought he could use a "mini ghetto blaster".
Because there was nothing similar to Thinkiverse, I sat down and pieced myself together.

Meanwhile I have several versions of it here. You can just puzzling those who like you better.

Version 1 is with built-in battery pack 12V li-ion
Version 2 is for AA batteries.

Current status of the project is: waiting for ordered parts

Parts list for the PE3D mini ghettoblaster.

for printing:

Maincase 5-15% Infill / 0.2mm Layer - OK
Front 15% infill / 0.1 - 0.15mm layer + Support 5% - OK
Backcover 5% - 15% Infill / 0.2mm Layer OK
Backcover for Batterie Version 20% /0.2mm + Support 10% - OK
Grid 1-3 100% Infill / 0.1mm Layer + Support 15% - OK
Grid v2 100% Infill / 0.1mm Layer - OK
Handle.stl 50% infill / 0.2mm layer - OK
Handle Beltholder 100% Infill 0.1mm Layer - OK
VolKnob.stl 80-100% infill / 0.2mm layer - OK

Speaker broadband 2x 50mm 10W 4ohm
https://goo.gl/PRKcwU
or
https://goo.gl/PYiFfh

On / Off switch 10pcs
https://goo.gl/htsDiu

Battery + power supply or Batteryholder
https://goo.gl/PhahMV
https://goo.gl/UDsV4C
or u can use 3x 18650 Li-ion Batteries because the ready set in the Link are cheaper.

Amplifier 2x10W PAM8610 Stereo Class D
https://goo.gl/sdbuZX

Antenna 25.4cm 5 sections
https://goo.gl/kbzG8J

Led version 3mm 10pcs
https://goo.gl/Thpe7u

Led 3mm 100pcs
https://goo.gl/mv6Sn1

DC plug installation 5.5-2.1mm 5pcs
https://goo.gl/PXB7NU

MP3 / Bluetooth / USB Player
https://goo.gl/6EQAGG
or
https://goo.gl/ZzjhQZ

additional is required:

-ca. 20cm 2x0,5mm cable for the speakers

• acoustic wadding or similar to insulating the housing
  Screws metric 8x M3x10-25mm + nuts and washers (for mounting the speakers)
  -Screws Metric 5x M5x10-25mm for the lid
  -Screws for plastic joint countersunk 2x approx 3x10 (for the player) holes must be pre-drilled!

Plastic Adhesive (Uhu Allplast)
Soldering iron and solder
Shrink tubing or insulation tape

The project is still under development.
Pressure and assembly, only on receipt of the parts.
Then come real photos.

Have fun while rebuilding and listening to music
If you want to give me a donation for this work, I would be very happy about it.

Changelog:
09-11-17 Frontplate new designed for better Print.
10-11-17 Frontplate testprint was ok, but not perfekt, Corner adapted to improve haptics.
10-11-17 Handle v3 Testprint was ok, but the part needs more infill. 15% to are to less -> 40%. Results much better.
12-11-17 Maincase Update, Holes für a Screw to Fix the Handle
13-11-17 Maincase Update, Bassreflextubes for little bit better Bassperformance
13-11-17 Added Maincase Battery version and matching rear panel and lid added.
14-11-17 Update Handle v 3, take holes for Screws, Update Maincase v2. Best Results are by 50% Infill
15-11-17 Grid v3 added
15-11-17 Cover for the Batteryversion addet Place for Switch Chargin or not, to make charging off if u use normal Batteries or Akkus & Update the Batterycover.