Parkside PPWD 30 A1 Vaccum Eurobox Cyclone 3D Printer Model
The file 'Parkside PPWD 30 A1 Vaccum Eurobox Cyclone 3D Printer Model' is (stl,STL,STEP) file type, size is 20.3MB.
The file 'Parkside PPWD 30 A1 Vaccum Eurobox Cyclone 3D Printer Model' is (stl,STL,STEP) file type, size is 20.3MB.
Clip in Eurobox Cyclone for Parkside PPWD 30 A1.
Eurobox used: 1a-TopStore Design Eurobox 40x30x18 cm. Foam seal needs to be added to the lid.
https://www.1a-topstore.eu/?a=5642&lang=eng
Depending on the planned project, a higher box could be a better fit.
The printed Euro_Box_Support parts are needed so that the vacuum will not deform the box and create a vacuum leak.
Original hose connectors need to be disassembled to fit 3D printed adapters.
Hose with an inner diameter of 38mm needed and a minimum length of 1.5m.
This cyclone is a remix of: https://www.thingiverse.com/thing:5579910
For assembly, see original cyclone.
All connectors are osVAC neo for a 38mm Hose. See https://www.thingiverse.com/thing:5253018 for more information.
Following parts need to be printed twice:
Cyclone_Lid_Support_outerside.stl
Cyclone_Lid_Support_innerside.stl
Euro_Box_Support_1.stl
Euro_Box_Support_2.stl
Cyclone_Box_Connector.stl (for assembly, mark middel of box and aligning with small notch on part)
The following parts are optional only if you want to use OsVAC connector on the end of the vacume hose:
Parkside_Hose_Connector_3.stl
Parkside_Hose_Connector_OsVAC_to_Nozzle.stl
| Cyclone_Box_Connector.stl | 101.6KB | |
| Cyclone_Fitting_1.stl | 487.3KB | |
| Cyclone_Fitting_2.stl | 1.2MB | |
| Cyclone_Lid_Support_innerside.stl | 303.8KB | |
| Cyclone_Lid_Support_outerside.stl | 326.1KB | |
| Euro_Box_Support_1.stl | 96.5KB | |
| Euro_Box_Support_2.stl | 137.3KB | |
| FLANGE_RING-01.STL | 2.1MB | |
| GLUED_FLANGE-02_for_starow.STL | 2.5MB | |
| Hose38_Female_osVAC_Neo.stl | 1.8MB | |
| Hose38_Male_osVAC_Neo.stl | 1.6MB | |
| INTAKE_SWIRL-01.STL | 21.7MB | |
| OUTLET_LID-03_for_starow.STL | 18.0MB | |
| Parkside_Hose_Connector_1.stl | 6.0MB | |
| Parkside_Hose_Connector_2.stl | 1.4MB | |
| Parkside_Hose_Connector_3.stl | 1.5MB | |
| Parkside_Hose_Connector_OsVAC_to_Nozzle.stl | 663.7KB | |
| SL_ST_TWO-STAGE_CYCLONE_SEPARATOR-06.STEP | 26.0MB | |
| SL_ST_TWO-STAGE_CYCLONE_SEPARATOR_SEDOND_STAGE_MKII_KEEPSV-00.STEP | 3.0MB | |
| SL_ST_TWO-STAGE_CYCLONE_SEPARATOR_SEDOND_STAGE_MKII_KEEPSV-00.STL | 12.7MB | |
| SL_ST_TWO-STAGE_CYCLONE_SEPARATOR_SEDOND_STAGE_MKII_KEEPSV-01.STL | 3.4MB | |
| SL_ST_TWO-STAGE_CYCLONE_SEPARATOR_SEDOND_STAGE_MKII_KEEPSV-02.STL | 2.3MB |
