Nutcracker Marvin 3D Printer Model
The file 'Nutcracker Marvin 3D Printer Model' is (stl) file type, size is 2.0MB.
The file 'Nutcracker Marvin 3D Printer Model' is (stl) file type, size is 2.0MB.
Nutcracker soldier designed to be printed in parts to allow separate colors without requiring an MMU.
Notes:
Arms, Legs - work best when printed with a brim.
Arms/Arm pins/Cuffs/Hands/Legs/Shoes/Soles/Laces (and the parts to go with them) - print 2x, there is no difference between the left and right.
Shoe spots - work best when printed with flat side down. Kind of confusing, but left spot and right spot are the left side and right side of each shoe as if you are wearing it.
Shoe laces are a tight fit, I just used a rubber mallet to seat them.
Brush - works best if printed with flat post end down and bristles up with supports to build plate with ‘top contact z distance’ set to 0.2 in print settings (prusa printer).
Base without date included.
Over hang parts like the eye insets - may require a little cleanup to accept the printed part.
Assemble the head in the main helmet first, then glue the helmetBase on (the head will not be able to slide in past the base if the helmet is glued together first. This is the only part that should require glue, but all pieces can be glued if fit is sloppy.
Assemble the shoes on the plate first as the legs go through them to the plate.
Scaling might work, I have not tried. There are some tight tolerances, so may not work.
| NutcrackerMarvinArm.stl | 50.1KB | |
| NutcrackerMarvinArmPin.stl | 21.3KB | |
| NutcrackerMarvinBase0.stl | 20.8KB | |
| NutcrackerMarvinBase2.stl | 14.5KB | |
| NutcrackerMarvinBase2022.stl | 156.0KB | |
| NutcrackerMarvinBaseBlank.stl | 91.5KB | |
| NutcrackerMarvinBelt.stl | 123.6KB | |
| NutcrackerMarvinBody.stl | 232.8KB | |
| NutcrackerMarvinBrush.stl | 3.7MB | |
| NutcrackerMarvinCuff.stl | 150.1KB | |
| NutcrackerMarvinEyeLeft.stl | 29.3KB | |
| NutcrackerMarvinEyePupilLeft.stl | 7.4KB | |
| NutcrackerMarvinEyePupilRight.stl | 7.4KB | |
| NutcrackerMarvinEyeRight.stl | 29.3KB | |
| NutcrackerMarvinHand.stl | 1.3MB | |
| NutcrackerMarvinHead.stl | 228.0KB | |
| NutcrackerMarvinHelmet.stl | 561.4KB | |
| NutcrackerMarvinHelmetBase.stl | 99.6KB | |
| NutcrackerMarvinHelmetVisor.stl | 121.0KB | |
| NutcrackerMarvinLeg.stl | 48.5KB | |
| NutcrackerMarvinLever.stl | 98.8KB | |
| NutcrackerMarvinLeverPinCover1.stl | 6.8KB | |
| NutcrackerMarvinLeverPinCover2.stl | 19.1KB | |
| NutcrackerMarvinShoe.stl | 117.7KB | |
| NutcrackerMarvinShoeLaces.stl | 18.8KB | |
| NutcrackerMarvinShoeSole.stl | 51.1KB | |
| NutcrackerMarvinShoeSpotLeft.stl | 7.1KB | |
| NutcrackerMarvinShoeSpotRight.stl | 7.1KB |
