MHW: Red Dragon – Safi Jiiva By PittRBM Sectioned For Resin Printing 3D Printer Model
The file 'MHW: Red Dragon – Safi Jiiva By PittRBM Sectioned For Resin Printing 3D Printer Model' is (stl) file type, size is 173.5MB.
The file 'MHW: Red Dragon – Safi Jiiva By PittRBM Sectioned For Resin Printing 3D Printer Model' is (stl) file type, size is 173.5MB.
MHW: Red Dragon - Safi Jiiva, sectioned for printing full size on Anycubic Photon resin printer
This is a remix from https://www.thingiverse.com/thing:4406835
The artist is Pitt Hutacharern. Visit his page at https://www.thingiverse.com/pittrbm/designs for more great creations.
Since this gorgeous creation is too big for most people to print I have sliced it into sections that will fit on the bed of an Anycubic Photon resin printer.
Each piece has a tab and slot to help line it up during assembly. Each tab has a 1mm clearance. Keep in mind that this will be affected if you change the scaling, which could cause problems during assembly.
There are 15 sections and it will probably take at least 14 print sessions so this is not a minor undertaking. It will require a LOT of resin even if you hollow the pieces, which I would not recommend for anything except the body unless you are experienced with hollowing resin prints.
I have also included the wings as whole pieces for those with larger printers or who are reducing the scale. They will fit whole at 45% reduction, which is apparently a good fit for use with a gargantuan sized miniature base.
It was a lot of work to prepare so please let me know if you find any errors. Please also note that I do not wish to cause any one to become upset. I actually hadn't intended to do anymore remixes, but I just couldn't resist this challenge. I apologize in advance to anyone who feels my work is offensive, I mean no harm.
All credit goes to the artist, Pitt Hutacharern. All I did was make it printable on resin printers. Please visit his page at https://www.thingiverse.com/pittrbm/designs for more terrific sculptures!
Again, the original sculpture can be found at https://www.thingiverse.com/thing:4406835
Additional note: the dragon is from Monster Hunter: World, and all design and copyright belong to CAPCOM
Edit: Shortened all the pins since there apparently wasn't enough clearance. Also repaired the holes along the edge of the right wing (that wing gave me problems right from the start) and double-checked all the files for errors.
| ph_body_lower.stl | 9.1MB | |
| ph_body_upper.stl | 15.4MB | |
| ph_head.stl | 13.4MB | |
| ph_leg_back_left.stl | 32.6MB | |
| ph_leg_back_right.stl | 31.0MB | |
| ph_leg_front_left.stl | 28.7MB | |
| ph_leg_front_right.stl | 25.4MB | |
| ph_tail_lower.stl | 25.4MB | |
| ph_tail_upper.stl | 6.1MB | |
| ph_wing_left_lower_A.stl | 14.7MB | |
| ph_wing_left_lower_B.stl | 16.8MB | |
| ph_wing_left_upper.stl | 4.7MB | |
| ph_wing_right_lower_A.stl | 43.0MB | |
| ph_wing_right_lower_B.stl | 47.7MB | |
| ph_wing_right_lower_B_repaired.stl | 39.4MB | |
| ph_wing_right_upper.stl | 41.2MB | |
| wing_left_whole.stl | 42.9MB | |
| wing_right_whole.stl | 39.8MB |
