Description Files (63)

Summary

MagHex Walls for Gloomhaven

This is a set of walls for use with my MagHex Tile System for Gloomhaven. These walls have magnets and wire nail holes in strategic locations that allow you to securely place them on the MagHex center mag tiles.

Features

There are wall sections to work as both "flat to flat" and "point to point" so you should be able to build every scenario in the book. (Untested)
Want doors for your scenario? Check out MagHex Doors that work with this system.
Three ways to use MagWalls with MagHex Tiles:
1. Press fit 3x3mm neodymium magnets into slots on the bottom of the wall segments. It's a friction tight fit and requires no glue.
2. Press #19 x 1/2" Wire Nails into recessed holes on the bottom of the wall segments.
  a.(Nail dimensions: 13.5mm long; 2.2mm diameter head; .5mm thick head; 1.1mm diameter shaft)
3. Glue MagWall segments to MagHex Blank or Terrain tiles.

Notes

MagWall sections come in 3 types:
1. F type - Used on Flat to Flat sections of terrain
2. P type - Used on Point to Point sections of terrain
3. C type - Used to link sections together at a corner
MagWalls use 3x3mm neodymium magnets that you can buy in bulk from ali express or ebay.
The polarity of the magnets needs to all face the same direction and match the polarity of the center magnets used in the center mag bases.
The wire nails can be bought in large packs for very little ($1.50) from any home improvement store. (Home Depot, Lowes, Ace, etc.)
Some wire nails will have to be cut shorter so they wont extend out the top of the model.
These walls are under construction! Proceed at your own peril! (hehe)

Changelog

04.23.2020

Added Ashlar C4 corner wall. Thanks for the idea bshigenaka!

03.17.2020

Added Ashlar F4 wall

09.22.2019

Added 2 more Wood walls per Nephilim2001's request.

06.12.2019

Added 3 more Ashlar walls.

06.10.2019

Updated the Ashlar wall type with a deeper texture. The test print didn't have enough definition to paint easily.

06.08.2019

Added a new type of wall! Ashlar! It's similar to Cobble, only not ruined. There are 8 pieces to try when you're building your next scenario!

06.02.2019

Added 7 Forest Bush walls. Thanks to RobagoN for the original design and idea!
Added Forest Grass wall. Print at .4 layer height, 100% infill. Cut away the cylinder. Press magnet in first, then use a blow dryer to shape the strands. Thanks to RobagoN for the idea!

05.30.2019

Made 3 new Wood wall segments

05.27.2019

Made 11 Stone walls segments! These have a cavern like appearance that looks very similar to the original tile art.
Added 4 Forest themed wall segments. The giant mushroom has to be printed in two parts and then glued together. I want to make more forest themed things, but I'm fresh out of ideas. Please post a comment with suggestions!

05.25.2019

Split MagHex Doors into their own thing to reduce clutter

05.20.2019

Added 2 Cobble Doors. Went with a metal look for the door itself, but I may also add a wood looking option as well.

05.19.2019

Added 2 Wood Doors! This took a lot more time and effort than I expected, but I think they turned out lovely. These are obviously heavily inspired by Rbross' door design.

05.18.2019

Added 2 Cobble wall segments

05.16.2019

Modified the wood corner segments to work a bit better

05.15.2019

Added 4 Wood Corners
Added 2 Wood Walls
Changed Naming Scheme to better reflect where/how a wall section should be used

05.12.2019

Added 3 Cobble Corners

05.11.2019

Updated design of the magnet slot with a slope to make it easier to insert
After tested with earring posts, I found out that they did not offer enough magnetism.
Switched all earring posts with wire nails
Changed magnet and wire nail intervals to better align with MagHex Bases
Reduced width of cobblestone wall segments (save filament and take up less space)
Added some texture to the plaster areas of the wood wall segments
Added 2-tile wood wall segment

05.09.2019

Updated design to use earring flat posts
Added 1 wood design

05.05.2019

Uploaded the first batch of Cobblestone walls. More to follow...

MagHex_Wall_Ashlar_C1_V1.1.stl	5.8MB
MagHex_Wall_Ashlar_C2_V1.1.stl	1.7MB
MagHex_Wall_Ashlar_C3_V1.1.stl	1.7MB
MagHex_Wall_Ashlar_C4_V1.1.stl	1.9MB
MagHex_Wall_Ashlar_F1-1_V1.1.stl	1.6MB
MagHex_Wall_Ashlar_F2-1_V1.1.stl	4.0MB
MagHex_Wall_Ashlar_F3-1_V1.1.stl	6.7MB
MagHex_Wall_Ashlar_F4-1_V1.1.stl	8.7MB
MagHex_Wall_Ashlar_F5-1_V1.1.stl	10.2MB
MagHex_Wall_Ashlar_P1-1_V1.1.stl	1.8MB
MagHex_Wall_Ashlar_P2-1_V1.1.stl	3.2MB
MagHex_Wall_Ashlar_P3-1_V1.1.stl	5.0MB
MagHex_Wall_Ashlar_P5-1_V1.1.stl	9.5MB
MagHex_Wall_Forest_Bush_C1-1_V1.stl	1.1MB
MagHex_Wall_Forest_Bush_F2-1_V1.stl	1.2MB
MagHex_Wall_Forest_Bush_F3-1_V1.stl	1.9MB
MagHex_Wall_Forest_Bush_F5-1_V1.stl	2.6MB
MagHex_Wall_Forest_Bush_P2-1_V1.stl	985.6KB
MagHex_Wall_Forest_Bush_P3-1_V1.stl	1.3MB
MagHex_Wall_Forest_Bush_P5-1_V1.stl	2.4MB
MagHex_Wall_Forest_Grass_C1_V1.1.stl	1.0MB
MagHex_Wall_Forest_Mushrom_Top_C1_V1.stl	389.9KB
MagHex_Wall_Forest_Mushroom_Base_C1_V1.stl	1.1MB
MagHex_Wall_Forest_Rock_C1_V1.stl	5.9MB
MagHex_Wall_Forest_Rock_F2-1_V1.stl	3.9MB
MagHex_Wall_Forest_Tree_F5-1_V1.stl	5.5MB
MagHex_Wall_Stone_C1_V1.stl	640.6KB
MagHex_Wall_Stone_F1-1_V1.stl	932.1KB
MagHex_Wall_Stone_F1-2_V1.stl	863.9KB
MagHex_Wall_Stone_F2-1_V1.stl	1.6MB
MagHex_Wall_Stone_F3-1_V1.stl	2.1MB
MagHex_Wall_Stone_F4-1_V1.stl	2.8MB
MagHex_Wall_Stone_F5-1_V1.stl	3.3MB
MagHex_Wall_Stone_P1-1_V1.stl	740.1KB
MagHex_Wall_Stone_P2-1_V1.stl	1.3MB
MagHex_Wall_Stone_P3-1_V1.stl	2.0MB
MagHex_Wall_Stone_P5-1_V1.stl	3.8MB
MagHex_Wall_Wood_C5_V1.5.stl	3.0MB
MagHex_Wall_Wood_F3-1_V1.4.stl	4.0MB
MagHex_Wall_Wood_F4-1_V1.4.stl	5.1MB
MagHex_Wall_Wood_P2-1_V1.4.stl	1.9MB
MagHex_Wall_Wood_P5-1_V1.4.stl	5.1MB
MagWall_Cobble_C1_v1.4.stl	1.4MB
MagWall_Cobble_C2_v1.4.stl	1.3MB
MagWall_Cobble_C3_v1.4.stl	1.0MB
MagWall_Cobble_F1-1_V1.4.stl	249.1KB
MagWall_Cobble_F1-2_V1.4.stl	158.1KB
MagWall_Cobble_F1-3_V1.4.stl	183.8KB
MagWall_Cobble_F2-1_V1.4.stl	693.9KB
MagWall_Cobble_F2-2_V1.4.stl	491.2KB
MagWall_Cobble_F3-1_V1.4.stl	954.8KB
MagWall_Cobble_F4-1_V1.4.stl	1.0MB
MagWall_Cobble_F5-1_V1.4.stl	1.2MB
MagWall_Cobble_P3-1_V1.4.stl	749.0KB
MagWall_Cobble_P5-1_V1.4.stl	1.3MB
MagWall_Wood_C1_V1.5.stl	1.2MB
MagWall_Wood_C2_V1.5.stl	1.4MB
MagWall_Wood_C3_V1.5.stl	989.9KB
MagWall_Wood_C4_V1.5.stl	1.4MB
MagWall_Wood_F1-1_V1.4.stl	1.2MB
MagWall_Wood_F2-1_V1.4.stl	2.5MB
MagWall_Wood_P1-1_V1.4.stl	1.3MB
MagWall_Wood_P3-1_V1.4.stl	2.5MB

MagHex Walls For Gloomhaven 3D Printer Model