Jensen Model 75 Steam Engine 3D Printer Model
The file 'Jensen Model 75 Steam Engine 3D Printer Model' is (stl,ipt,iam) file type, size is 16.2MB.
The file 'Jensen Model 75 Steam Engine 3D Printer Model' is (stl,ipt,iam) file type, size is 16.2MB.
Completely works with Drive Dimension. No Inferences detected.
All parts are listed below. This project was modeled after a Jensen Model 75 Steam Engine Toy.
Comment with any criticism or critiques.
| Assembly1.stl | 8.2MB | |
| Base.ipt | 294.5KB | |
| Basin_Gasket.ipt | 76.5KB | |
| Bracket_Curvy_Thing.ipt | 128.0KB | |
| Bracket_Pipe.ipt | 112.0KB | |
| Burning_Piece.ipt | 262.5KB | |
| Coil.ipt | 347.5KB | |
| copper_top.ipt | 125.5KB | |
| crank.ipt | 125.0KB | |
| Crankshaft.ipt | 64.0KB | |
| Crankshaft_Sub-assembly.iam | 67.0KB | |
| Crankshaft_Support.ipt | 109.0KB | |
| Cylinder.ipt | 99.5KB | |
| Cylinder_Assembly.iam | 97.0KB | |
| Cylinder_Assembly.ipt | 293.5KB | |
| Cylinder_Cap_Back.ipt | 96.0KB | |
| Cylinder_Cap_Front.ipt | 109.0KB | |
| Cylinder_Support.ipt | 120.5KB | |
| Eccentric_Assembly.iam | 83.0KB | |
| eccentric_hub.ipt | 126.0KB | |
| Eccentric_Pulley.ipt | 178.5KB | |
| eccentric_screw.ipt | 104.0KB | |
| eccentric_slider_thing.ipt | 157.0KB | |
| eccentric_straps.ipt | 89.0KB | |
| Eccentric_Washer.ipt | 81.5KB | |
| Exhaust.ipt | 83.5KB | |
| flywheel.ipt | 337.0KB | |
| Flywheel_Base.ipt | 342.0KB | |
| Fly_Wheel_Base_-_Moll.ipt | 741.5KB | |
| Fuel_Bay.ipt | 197.5KB | |
| Fuel_Tray.ipt | 120.5KB | |
| Handle_Rod.ipt | 69.5KB | |
| ISO_13337_-_2_x_4ISO.ipt | 143.5KB | |
| ISO_4032_-_M2ISO.ipt | 161.5KB | |
| ISO_7045_-_M3_x_6_-_4.8_-_HISO.ipt | 272.5KB | |
| Linkage_Rod.ipt | 101.0KB | |
| Model_Plate.ipt | 2.2MB | |
| Motor_Assembly.iam | 109.5KB | |
| Motor_Assembly_2.iam | 256.0KB | |
| Motor_Mount2.ipt | 464.0KB | |
| Motor_Strap.ipt | 113.0KB | |
| Motor_Strap_1_2.ipt | 381.0KB | |
| Motor_Strap_2_2.ipt | 379.5KB | |
| Pipe1.ipt | 105.0KB | |
| Pipe2.ipt | 71.0KB | |
| Piston.ipt | 130.0KB | |
| Piston_Head.ipt | 135.5KB | |
| Piston_Pin.ipt | 106.5KB | |
| Piston_Ring.ipt | 89.5KB | |
| Piston_Rod.ipt | 74.0KB | |
| Plastic_Cap.ipt | 277.0KB | |
| pressure_release.iam | 78.0KB | |
| pressure_release_body.ipt | 124.5KB | |
| pressure_release_coil.ipt | 317.5KB | |
| pressure_release_rod.ipt | 89.5KB | |
| pressure_release_washer.ipt | 74.5KB | |
| Pulley.ipt | 175.5KB | |
| Rattle.ipt | 97.5KB | |
| Rattle_Bracket.ipt | 168.5KB | |
| Rivet.ipt | 137.5KB | |
| Rivet_GB_T_827-1986-2.5_X_3.ipt | 187.0KB | |
| Shaft.ipt | 95.0KB | |
| Shell.ipt | 308.5KB | |
| Spinning_thing.ipt | 131.5KB | |
| Steam_Chest.ipt | 157.5KB | |
| Steam_House_Extension.ipt | 255.0KB | |
| Steam_Housing.ipt | 327.0KB | |
| Steam_Pipe.iam | 95.0KB | |
| steam_pipe_bolt.ipt | 126.5KB | |
| steam_pipe_bracket.ipt | 158.5KB | |
| Steam_Pipe_Cap.ipt | 139.0KB | |
| Steam_Pipe_Valve.ipt | 142.5KB | |
| Steam_Pipe_Valve_Container.ipt | 124.5KB | |
| Steam_Whistle.iam | 87.5KB | |
| steam_whistle.ipt | 299.5KB | |
| Steam_Whistle_Main.ipt | 179.0KB | |
| Steam_Whistle_Nut.ipt | 130.0KB | |
| Steam_Whistle_Valve.ipt | 124.0KB | |
| Threaded_Cap.ipt | 544.0KB | |
| threaded_shaft.ipt | 112.5KB | |
| thread_water_cap.ipt | 111.5KB | |
| Tray.iam | 75.5KB | |
| Valve.ipt | 115.5KB | |
| Valve_Body.ipt | 222.5KB | |
| Valve_Handle_Red.ipt | 161.0KB | |
| WaterContainer.iam | 92.0KB | |
| Water_Basin.ipt | 293.5KB | |
| water_basin_strap.ipt | 98.5KB | |
| water_glass_cover.ipt | 71.0KB |
