ImmersionRC EzTracker Antenna Tracker Case 3D Printer Model Free Download

Description Files (46)

Summary

This is an adaptation of my Ghettostation Antenna Tracker design to fit the ImmersionRC EzTracker (currently version 1).

The case features:

0-135 degree Tilt Head
360 degree Pan mount (ball bearing supported)
Antenna quick change/release to allow use of multiple different antennas
ImmersionRC Duo 5800 V3 & V4 as well as Uno5800 V2 and Uno2400 Video RX mount (single mini DIN connection, lever for frequency selection)
Lawmate 2.4Ghz RX mount
3DR Radio Telemetry Module (900Mhz or 433 Mhz) mount on the tracking plate
Easy access Battery compartment for up to 3700mAh 4S LiPo Pack
EzTracker LCD mount with Easy access to the selection buttons and remaining module protected inside the case.
Mounts for Power On/Off, 4x Video out, 1x T-Style/Deans Power connector
Tripod Quickmount and additional feet for table top/car roof top positioning
Please refer to the instructions for details on the used components

In case you already have the Ghettostation Tracker printed, the only items to be changed are:

Case_front_Ez.stl
Cover_Front_Ez_v2.stl
Cover_Front_Ez_bottom.stl

Please note: The mounting plate for DUO5800 V4 is based on measurements received from ImmersionRC only. It has not yet been tested (I only have a V3). Please post here in case you have issues with the V4. Do also let us know in case it works perfectly as advertised :-). You will need to print 2 of the Duo5800_push.stl and Duo5800_lever.stl for the V4 of the DUO5800 as it has both Band and Frequency selection buttons.

27/1/2015:

Turnplate updated to allow removal of the top without the need to pull the cables through before.

29/1/2015:

Added RX mounts for ImmersionRC Uno5800 V2 and Uno2400 (same mount as Uno5800) receiver as well as Lawmate 2.4Ghz receiver

16/2/2015:

After receiving feedback that a large part of the files failed to print in Slic3r and Cura, I believe I found an error in the scaling method I used to export the files. All files are updated and check out in 3 slicers I have tested so far. Please report back in case there are still issues.
Other changes:

Added spacers for the bearings as, depending on servo and filament used there is a gap between bearing and turnplate. Print the required thickness and insert it between the bearing mount and the rear top cover
updated the rear case to allow the use of a M4 nut for the battery door as the plastic wears out after some time.
2 versions of the rear case are not available. 1 version comes with 4 video connectors and 1 Deans connector, the other with 2 video connectors, one deans and one XT60 connector.

01/03/2015:

Added mirror version of the Uno5800 Mount in case you want to install it on the left side or have one Uno5800 on one and a Uno2400 on the other side.

29/03/2015:

Corrected Uno2400 mount added (left and right side)

11/04/2015:

added modular Antenna mounts. Allows quick change of the following Antenna types:
1) ImmersionRC 5.8 Patch (IMRC5.8_Lock.stl)
2) ImmersionRC 2.4 Patch (IMRC2.4_Lock.stl)
3) Circular Wireless 5.8 Helix (CW5.8_Lock.stl)

You will need to replace the tilt head plate with the new lock plate (Head_Lock.stl).

30/07/2015:

added a quick 4 part version of the case to print on smaller printers.
Part 1 needs to be glued to part 2 and part 3 needs to be glued to part 4 along the split line. Please report back in case you face issues.

CutCase_Ez_part1.stl
CutCase_Ez_part2.stl
CutCase_Ez_part3.stl
CutCase_Ez_part4.stl

3DR_Case_v2.stl	36.9KB
Antenna_plate_v2.stl	182.6KB
arm1_v2.stl	92.6KB
arm2_v2.stl	127.0KB
Arm_base_v2.stl	67.4KB
BatteryScrew_v2.stl	67.5KB
Battery_Cover_v2.stl	8.3KB
Bearing_Spacer_1.5mm_v2.stl	36.8KB
Bearing_Spacer_1mm_v2.stl	36.8KB
Bearing_Spacer_2.5mm_v2.stl	36.8KB
Bearing_Spacer_2mm_v2.stl	36.8KB
Bearing_Spacer_3mm_v2.stl	36.8KB
Bearing_v2.stl	114.1KB
Case_front_Ez_v2.stl	164.9KB
Case_rear_2vid_v2.stl	235.8KB
Case_rear_v2.stl	252.8KB
Cover_Front_Ez_Bottom_V2.stl	58.3KB
Cover_front_Ez_v2.stl	44.0KB
Cover_rear_v2.stl	80.2KB
CutCase_Ez_part1.stl	188.0KB
CutCase_Ez_part2.stl	67.9KB
CutCase_Ez_part3.stl	110.5KB
CutCase_Ez_part4.stl	57.5KB
CW5.8_Lock.stl	108.8KB
CW_holder_v2.stl	45.4KB
CW_mount_v2.stl	93.8KB
CW_spacer_v2.stl	9.5KB
Duo5800V3_v2.stl	125.5KB
Duo5800V4_v2.stl	121.3KB
Duo5800_lever_v2.stl	29.8KB
Duo5800_push_v2.stl	7.7KB
Foot_v2.stl	49.3KB
gws_spacer_v2.stl	10.4KB
Head_Lock.stl.stl	92.6KB
IMRC2.4_Lock.stl	180.0KB
IMRC5.8_Lock.stl	142.5KB
Lawmate_2.4Ghz_v2.stl	66.4KB
Patch_mount_v2.stl	87.0KB
Pin_v2.stl	27.6KB
pivot1_v2.stl	39.6KB
pivot2_v2.stl	35.4KB
Tripod_mount_v2.stl	33.3KB
Uno2400_V1.stl	100.4KB
Uno2400_V1_left.stl	100.4KB
Uno5800_V3.stl	118.8KB
Uno5800_V3_left.stl	118.8KB

ImmersionRC EzTracker Antenna Tracker Case 3D Printer Model

Summary

Tags

You might also like