The file 'Flexible Goggles Optimised For 3DP [Print On Transparent Film Challenge] 7-size Covid-19 3D Printer Model' is (stl) file type, size is 22.5MB.
Yet another easy printable and usable Goggles. [Optimised for 3D Print on Transparent Film].
Goggles weight 29gram (Stripe inclusive).
Speed Build Video
https://youtu.be/TRsTjk00IgQ
Don't forget to subscribe my Channel. https://www.youtube.com/c/iczfirz
=====================================================
(---- Notice ----)
It is just TOO DANGEROUS to put on your face, it is too brittle. If a PLA mask cracks, it will cut your face and eyes like a knife.
A fatal scenario could be something may strike your PLA mask like poor Kevin in the following videos:
For Part 1 in PLA please go here: https://youtu.be/ErP28uP4mVI
For Part 2 in PLA please go here: https://youtu.be/LlN01EW9ORI
For Part 3 in ABS please go here : https://youtu.be/feWsPd2XUFU
For Part 4 in PET-G please go here : https://youtu.be/k-KhRx73NxU
=====================================================
Files explain.
Why Goggles_Top_Aligned? It give the best 3D print result as there is no nozzle travel at all. So zero Oozing. The trade off is you need more time and tpu per print. (39g vs 22g. 2h14m vs 1h25m.). And you need to trim it by a pair of scissors.
Setup new Cura Profile
Material
-Generic TPU 95A (reminder. Cura default extruder setup is 2.86mm. You may need to set it to 1.75mm.)
Print Settings (Setup new Profile base on stock Extra Fast 0.3mm base profile)
-Custom
Profile
-Extra Fast -0.3mm
Layer Height
-0.3mm
Initial Layer Height
-0.2mm
Wall Thickness
-1.2mm
Fill Gaps Between Walls
-Nowhere
Seam Corner Preference
-None
Infill Density
-100%
Build Plate Temperature
-20degC
Build Plate Temperature Initial Layer
-50degC
Layer Start X
-0 (delta), or
-Max X size / 2 (Rectangle bed. Lower Left as origin)
Layer Start Y
-0 (delta), or
-Max Y size / 2 (Rectangle bed. Lower Left as origin)
Skirt Line Count
-3
**Fine tune retraction (I use 5mm) speed (I use 60mm/s) and extra prime (I use 0mm) for your extruder and TPU.
Preview slice result. Follow the check list below (Picture from Rolley Mask but 4 walls for Googles):
Addiction to 3D Printing? Watch these time-lapse!
https://youtu.be/uNqqN5Ao_hI
https://youtu.be/-ZsXFX6hjXk
https://youtu.be/L4IDmn3miE0
https://youtu.be/y3-0Y90HoYo
| Goggles_Cover_L.stl | 673.7KB | |
| Goggles_Cover_M.stl | 673.7KB | |
| Goggles_Cover_S.stl | 673.7KB | |
| Goggles_Cover_XL.stl | 673.7KB | |
| Goggles_Cover_XS.stl | 673.7KB | |
| Goggles_Cover_XXL.stl | 673.7KB | |
| Goggles_Cover_XXS.stl | 673.7KB | |
| Goggles_L.stl | 2.8MB | |
| Goggles_M.stl | 2.8MB | |
| Goggles_S.stl | 2.8MB | |
| Goggles_Top_Aligned_L.stl | 2.8MB | |
| Goggles_Top_Aligned_M.stl | 2.8MB | |
| Goggles_Top_Aligned_S.stl | 2.8MB | |
| Goggles_Top_Aligned_XL.stl | 2.8MB | |
| Goggles_Top_Aligned_XXL.stl | 2.8MB | |
| Goggles_Top_Aligned_XXS.stl | 2.8MB | |
| Goggles_XL.stl | 2.8MB | |
| Goggles_XS.stl | 2.8MB | |
| Goggles_XXL.stl | 2.8MB | |
| Goggles_XXS.stl | 2.8MB | |
| Optional_Buckle2slot7mmStripeWidth.stl | 127.5KB | |
| Optional_Buckle4slot7mmStripeWidth.stl | 904.0KB | |
| Roll_of_Stripe.stl | 1.4MB |
