Electronic Component Stackable Drawers 3D Printer Model
The file 'Electronic Component Stackable Drawers 3D Printer Model' is (stl) file type, size is 410.6KB.
The file 'Electronic Component Stackable Drawers 3D Printer Model' is (stl) file type, size is 410.6KB.
This remix offers a set of drawers with a height of 20mm and 40mm and both a width of ~19 cm. You can choose between thin walls (0.8mm) that are easy to print but a little wobbly and sturdier walls that are 1mm wide but require some special slicer settings. Additionally a version with a height of 20mm but only with a width of 16cm.
The shelves for the drawers are identical for the 0.8mm and 1mm variants.
The abbreviations for the file names are FB = FrontToBack divider, LR = LeftToRight divider. The narrow ones are named with 20s.
I print the 1mm variant with PLA with following Cura-Slicer-settings:
Layer height: 0.3
Init. Layer height: 0.2
Line Width: 0.53
Initial Layer Line Width: 60%
Wall thickness: 1.06mm
Wall Line count: 2
Optimize Wall Print order: Off
Compensate Wall overlaps:Off
Fill gaps between walls: Everywhere
Filter Out tiny gaps:ON
Infill: 10% (Gyroid)
Nozzle-Temp:215C
Bed Temp:40C
Flow:90%
Infill speed: 60mm/s
Wall speed: 50mm/s
Top/Btm Speed:60mm/s
Init. layer speed: 50mm/s
Retraction distance:6mm
Retraction Speed:40mm/s
Retraction extra prime amount: 1mm³ (Without I got under extrusion after a retraction and a long travel)
(Experimental-Settings)
Small Hole Size: 7.0mm
Small Feature Speed: 40%
| 20s_1x.stl | 19.4KB | |
| 20s_2x_FB.stl | 20.2KB | |
| 20s_2x_LR.stl | 20.2KB | |
| 20s_4x.stl | 21.8KB | |
| 20s_6x.stl | 23.3KB | |
| 20s_Base.stl | 105.6KB | |
| 20s_PlateFlat.stl | 170.9KB | |
| 20_08_10x.stl | 33.3KB | |
| 20_08_10x_FB.stl | 28.9KB | |
| 20_08_15x.stl | 37.2KB | |
| 20_08_18x.stl | 35.1KB | |
| 20_08_1x.stl | 26.3KB | |
| 20_08_25x.stl | 40.6KB | |
| 20_08_25x_5big.stl | 36.7KB | |
| 20_08_2x_FB.stl | 27.0KB | |
| 20_08_2x_LR.stl | 27.0KB | |
| 20_08_4x.stl | 28.6KB | |
| 20_08_4x_FB.stl | 28.6KB | |
| 20_08_6x.stl | 30.2KB | |
| 20_1_10x_Mix.stl | 28.9KB | |
| 20_1_1x.stl | 21.9KB | |
| 20_1_21x_Mix.stl | 37.5KB | |
| 20_1_22x_Mix.stl | 38.3KB | |
| 20_1_25x.stl | 40.6KB | |
| 20_1_25x_Mix.stl | 40.6KB | |
| 20_1_2x.stl | 22.6KB | |
| 20_1_4x.stl | 24.2KB | |
| 20_1_6x.stl | 25.8KB | |
| 20_1_9x.stl | 28.1KB | |
| 20_1_9x_Mix.stl | 28.1KB | |
| 20_Base.stl | 103.8KB | |
| 40_08_12x.stl | 36.7KB | |
| 40_08_18x.stl | 41.4KB | |
| 40_08_1x.stl | 28.1KB | |
| 40_08_1x_3x.stl | 30.5KB | |
| 40_08_24x.stl | 46.1KB | |
| 40_08_2x_FB.stl | 28.9KB | |
| 40_08_2x_LR.stl | 28.9KB | |
| 40_08_4x.stl | 30.5KB | |
| 40_08_4x_FB.stl | 30.5KB | |
| 40_08_4_2_2.stl | 33.6KB | |
| 40_08_6x.stl | 26.5KB | |
| 40_08_6x_FB.stl | 32.0KB | |
| 40_08_9x.stl | 34.4KB | |
| 40_1_16x.stl | 34.4KB | |
| 40_1_1x.stl | 22.6KB | |
| 40_1_2x.stl | 23.4KB | |
| 40_1_3x_FB.stl | 24.2KB | |
| 40_1_3x_LR.stl | 24.2KB | |
| 40_1_4x.stl | 25.0KB | |
| 40_1_6x.stl | 26.5KB | |
| 40_Base.stl | 114.3KB | |
| PlateFence.stl | 50.9KB | |
| PlateFlat.stl | 181.9KB |
