This Galleon is a work in progress.
OpenLock Connection Sockets:
Note that you need to remove the small bridge supports in the connection sockets. The sockets are imported from the open-lock dungeon tile system. These sockets have always seemed a little too snug to me, so printing the connector pieces at 90% high or so seems to help or I have to put a ton of force on the pieces to connect them, as well as shaving the inside with an Xacto knife. Preferably, I print these at 100% and put a lot of force to get them together.
Sails:
I've updated the model to include sails, which will require supports, unfortunately, and need to be glued together - super glue works best with PLA I've found.
Masts:
The capstan and masts will need to be glued down for now, though I will probably implement a way to snap them in. Note that with the addition of the sails, the rear mast needs to be replaced with the new one if you previously installed the older, taller mast on the rear of the ship.
Supports:
The only piece so far that requires support for me is the back piece of the captain's quarters since it has a large door overhang.
To do: helm, airship conversion pieces.
| Capstain.stl |
| Captain_Door.stl |
| Galleon_-_Captains_Quarters.stl |
| Galleon_-_Captains_Quarters2_fixed.stl |
| Galleon_-_Captains_Quarters3_fixed.stl |
| Galleon_-_Top_-_Deck.stl |
| Galleon_-_Top_-_Deck_with_Mast.stl |
| Galleon_-_Top_-_Grate_or_Stairs.stl |
| Galleon_-_Top_-_Nose.stl |
| Galleon_-_Top_-_Nose2.stl |
| Galleon_-_Top_-_Nose3.stl |
| Galleon_-_Top_-_Nose4.stl |
| Galleon_-_Top_-_Stairs_and_Door.stl |
| Gangplank_-_plain.stl |
| Gangplank_-_with_notches.stl |
| Grate.stl |
| Helm.stl |
| Helm2.stl |
| Kichen_Shelf_-_Top.stl |
| Kitchen_Door.stl |
| Kitchen_Shelf_-_Bottom.stl |
| Lower_Deck_-_Center_-_No_Pillar.stl |
| Lower_Deck_-_Center_-_Pillar.stl |
| Lower_Deck_-_Front_1.stl |
| Lower_Deck_-_Front_2.stl |
| Lower_Deck_-_Rear_1.stl |
| Lower_Deck_-_Rear_2.stl |
| Mast_-_Lower.stl |
| Mast_-_Lower_-_With_Ladder.stl |
| Mast_-_Rear.stl |
| Mid_Deck_-_Center_-_Stairs.stl |
| Mid_Deck_-_Center_-_With_Window.stl |
| Mid_Deck_-_Center_-_With_Window_and_Mast_Support.stl |
| Mid_Deck_-_Front_1.stl |
| Mid_Deck_-_Front_2.stl |
| Mid_Deck_-_Front_3.stl |
| Mid_Deck_-_Kitchen.stl |
| Mid_Deck_-_Rear_1.stl |
| Mid_Deck_-_Rear_2.stl |
| Mid_Deck_Window.stl |
| Ropeladder_Bottom.stl |
| Ropeladder_Center_Pieces.stl |
| Ropeladder_Top.stl |
| Sails_-_Lower_Sail_-_Center_-_Has_Ladder.stl |
| Sails_-_Lower_Sail_-_Rear_Front.stl |
| Sails_-_Top.stl |
| Sails_-_Top_-_Crows_Nest_-_Center.stl |
| Stairs_for_Gangplank_and_Ropeladder.stl |
| Tile_layout_iteration_3-ODT_openLock_nub.stl |
