If you like this design, buy me a beer :)
http://www.thingiverse.com/bendiger/about
UPDATE 09-17-16
Thanks to all the hard work of Nathan720 (http://www.thingiverse.com/Nathan720), there is now an instructables post for how to build the helmets!
http://www.instructables.com/id/Two-Daft-Punk-Helmets-in-One-Month/
All the parts will be for the left side and just need to be mirrored to print the right.
This design is for small 3D Printers with print beds 6x6in or bigger.
All parts Zip tie or glue together.
Support Material is a must unless you have a lot of faith in your printers capabilities and you can print extreme overhangs.
About 120 hours of printing so far, and 2 reels of 3mm abs.
It will be compatible with the AlexPlusLEDs matrix and side bar kits found here: http://alexplusleds.bigcartel.com/
STL files orientated for printing on a 6x6 bed.
Want the Guy Manuel Helmet? Here it is:
http://www.thingiverse.com/thing:470882
UPDATE 05-22-14: I've added the Visor to the list of files. Support material is required, I haven't made these with supports built-in yet, version 2 maybe.. More to follow soon.
UPDATE 05-26-14: I've added the dome parts. I'm still working on the electronics mounts, those might be a while..
UPDATE 09-01-14 I added the visor to the list of parts. This can be used to make molds from or bend plexiglass around and then cut to fit.
UPDATE: 09-20-14
Electronic mounts are finally done.
Helmet design for V1 is done.
Please tell me what changes you would like made. I want this to be the best version it can be.
UPDATE: 10-10-14
I've uploaded larger versions of all the parts after some feedback about the Guy Man helmet seeming larger. Turns out the Thomas was too small. The electronic mounts will be done soon. Little more work needed. The parts with v1.5 are the scaled versions. I've left the original parts.
UPDATE 10-26-15
Thought I should clarify some things since there seems to be some confusion. All of the parts that list v1.5 are a slightly larger version. the rest of the parts, 1.3, 1, and some without versioning, are the smaller helmet. There is an instructables that Fictive made recently on how to put the helmet together. http://goo.gl/cWfsDO
| DisplayLowerBracket-v1.3.stl | 236.8KB | |
| DisplayupperBracket-v1.3.stl | 219.1KB | |
| LightRing-v1.0.stl | 668.1KB | |
| LightRing-v1.5.stl | 727.1KB | |
| Thomas_Helmet-BottomVisor-Front-V1.5.stl | 1.8MB | |
| Thomas_Helmet-BottomVisor-Front.stl | 1.8MB | |
| Thomas_Helmet-Cheek-V1.5.stl | 1.8MB | |
| Thomas_Helmet-Cheek.stl | 1.8MB | |
| Thomas_Helmet-Dome-Back-Bottom-v1.5.stl | 733.2KB | |
| Thomas_Helmet-Dome-Back-Bottom.stl | 733.2KB | |
| Thomas_Helmet-Dome-Back-Mid-V1.5.stl | 1.3MB | |
| Thomas_Helmet-Dome-Back-Mid.stl | 1.3MB | |
| Thomas_Helmet-Dome-Back-Top-V1.5.stl | 1.8MB | |
| Thomas_Helmet-Dome-Back-Top.stl | 1.8MB | |
| Thomas_Helmet-Dome-Front-V1.5.stl | 1.6MB | |
| Thomas_Helmet-Dome-Front.stl | 1.6MB | |
| Thomas_Helmet-Dome-Side-V1.5.stl | 1.6MB | |
| Thomas_Helmet-Dome-Side.stl | 1.6MB | |
| Thomas_Helmet-Dome-SideTip-V1.5.stl | 577.5KB | |
| Thomas_Helmet-Dome-SideTip.stl | 577.5KB | |
| Thomas_Helmet-Dome-Top-V1.5.stl | 3.3MB | |
| Thomas_Helmet-Dome-Top.stl | 3.3MB | |
| Thomas_Helmet-EarCap-V1.5.stl | 6.6MB | |
| Thomas_Helmet-EarCap.stl | 6.6MB | |
| Thomas_Helmet-EarMount-v1.0.stl | 1.0MB | |
| Thomas_Helmet-EarMount-v1.5.stl | 1.0MB | |
| Thomas_Helmet-Mouth-V1.5.stl | 2.5MB | |
| Thomas_Helmet-Mouth.stl | 2.5MB | |
| Thomas_Helmet-TopVisor-Side-V1.5.stl | 933.9KB | |
| Thomas_Helmet-TopVisor-Side.stl | 933.9KB | |
| Thomas_Helmet-Visor-Side-V1.5.stl | 831.9KB | |
| Thomas_Helmet-Visor-Side.stl | 831.3KB | |
| Thomas_Helmet-Visor-TopFront-V1.5.stl | 1.3MB | |
| Thomas_Helmet-Visor-TopFront.stl | 1.3MB | |
| Thomas_Helmet-VisorL.stl | 782.2KB |
![Trench Raider [Sniper Plate And Face Mask] 3D Printer Model](https://res.3axis.co/4603959c-a0a0-4ecb-9060-3391742fca14/images/89603869-dc1f-4627-a3d5-ac5592398b26_thumb.jpg)
