You can prototype almost any kind of robotic platform or experimental laboratory equipment with these connectors.
Update 9/15
Update 6/23/14
These connectors will allow the fabrication of almost any shape or enclosure, using the 20x20 mm MakerBean type model from dbozec ( http://www.thingiverse.com/thing:27825 ). Especially desinged to facilitate the construction of experimental laboratory equipment and platforms. The connectors are meant to be glue-"welded" to each other with ABS acetone slurry or cyanomethacrylate (crazy glue).
With these connectors you can do end-end, corner, rail, groove, flat top or plate, sliding surface, T-pieces end to side and side to side connections, wire guides and mounting or fixation parts. You name it...
| 13_tooth_gear_idler.stl | 73.7KB | |
| 45_degree_angle_corner.stl | 49.2KB | |
| bolt_inset_foot_M6.stl | 126.3KB | |
| Corner2_Round_20mm_maker_rail.stl | 6.9KB | |
| Corner3_Insert_20mm_maker_rail.stl | 5.7KB | |
| Corner_Round_20mm_maker_rail.stl | 8.5KB | |
| Corner__Rounded_Hole_20mm_makerBeam.stl | 19.6KB | |
| Deep_groove_slider.stl | 5.2KB | |
| Deep_groove_slider_Peg.stl | 2.6KB | |
| Drive_belt_gear.stl | 48.5KB | |
| Drive_belt_gear_with_pinion_hub.stl | 91.0KB | |
| Final_Parts.zip | 2.0MB | |
| Flat.stl | 37.7KB | |
| Flat_End_Cap_for_20mm_rail.stl | 8.5KB | |
| flat_insert.stl | 2.4KB | |
| Foot_for_20mm_rail.stl | 26.4KB | |
| grooved.stl | 41.4KB | |
| Groove_Connector_narrow_for_raised_groove_20mm_Maker_rail.stl | 2.6KB | |
| Groove_Maker_rail_20mm.stl | 41.4KB | |
| Groove_Raised_Maker_rail_20mm.stl | 5.2KB | |
| HoldDownFlush.stl | 6.9KB | |
| Hold_Down_END.stl | 48.9KB | |
| Hold_Down_Foot_20mm_MakerRail.stl | 13.6KB | |
| Hold_Down_Sunken_But_Plate.stl | 33.3KB | |
| idler_end_mount.stl | 15.9KB | |
| Limit_switch_horizontal_1.5.stl | 18.4KB | |
| Limit_switch_horizontal_2.0.stl | 18.4KB | |
| Limit_switch_vertical.stl | 18.8KB | |
| Long_half_of_90_degree_for_20mm_rail.stl | 2.6KB | |
| pinion.stl | 71.0KB | |
| Plexiglass_2.5_mm_foot_grooved.stl | 5.4KB | |
| Plexiglass_2.5_mm_one_sided.stl | 3.4KB | |
| Plexiglass_2.5_mm_sheet_corner.stl | 12.2KB | |
| Plexiglass_2.5_mm_sheet_holder_base.stl | 3.8KB | |
| Plexiglass_2.5_mm_sheet_holder_side.stl | 3.4KB | |
| Plexiglass_2.5_mm_slide.stl | 4.2KB | |
| plexi_inline1.stl | 2.6KB | |
| plexi_inline2.stl | 3.4KB | |
| plexi_inline_offset.stl | 2.4KB | |
| rack1_repaired.stl | 35.6KB | |
| rack2.stl | 57.1KB | |
| roller_guide.stl | 8.3KB | |
| ServoHolderInLineHole.stl | 38.0KB | |
| ServoHolderOmni__repaired_.stl | 132.5KB | |
| ServoHolderSide.stl | 27.6KB | |
| Short_half_of_90_degree_for_20mm_rail.stl | 1.8KB | |
| Side_to_side_Joiner_for_20mm_rail.stl | 4.0KB | |
| slider.stl | 10.8KB | |
| Small_Mount_Front.stl | 38.2KB | |
| Small_Mount_Side_Base.stl | 1.8KB | |
| Small_Mount_Side_Top.stl | 36.2KB | |
| Small_Mount_Side_Top_Thick.stl | 36.2KB | |
| stepper_horizontal_mount.stl | 68.1KB | |
| stepper_mount_vertical.stl | 74.3KB | |
| stepper_rail_mount_blank_5mm_for_20mm_makerbeam.stl | 4.2KB | |
| Tall_end_to_end_connector_for_20mm_rail.stl | 1.8KB | |
| Thick_corner_20mm_maker_rail.stl | 2.6KB | |
| thumb_axle.stl | 68.6KB | |
| thumb_hold_down.stl | 6.1KB |
