Bolter Conversion For G36 Airsoft 3D Printer Model
The file 'Bolter Conversion For G36 Airsoft 3D Printer Model' is (stl) file type, size is 340.1KB.
The file 'Bolter Conversion For G36 Airsoft 3D Printer Model' is (stl) file type, size is 340.1KB.
This Kit is designed to fit on airsoft G36 replica's. In this case an SRC GEN 3 was used. It is designed to be fully removalable for maintanance. Its internal design ensures it fits snug and secure on the airsoft replica.
*Note if you have a G36 of another brand compatiblity cant not be promised and some small modification may be required. A TM compatible magwell has been provided as an optional part if required.
Glue (2 part epoxy was used)
Various grades of sandpaper (from 150 down to 3000, though this is optional and use your own discretion)
Allen keys (to affix the bolts)
(Bolts/screws are qty=2 (M4x25mm), qty=6 (M4X8mm), qty=2 (M4x12mm), qty=1 (M6X45mm) and you will need nuts for those 10x m4 and 1x M6
Bar Clamps (or other equipment to hold parts while glue sets)
Needle files (for finishing and adjusting fit)
FPlate - Front Plate
FrontSideL - Front Side Left
FrontSideR - Front Side Right
FGrip - Front Grip
MidSideL - Middle Side Left
MidSideR - Middle Side Right
MidGrip - Middle Grip
RearSideL - Rear Side Left
RearSideR - Rear Side Right
RailA1 - Front end of railsection
RailB1 - 2nd part of rail section
RailC1 - 3rd part of rail section
RailD1 - 4th part of rail section
Connector1 - First part of the upper rail section
Connector2 - 2nd part of upper rail section
Connector3 - 3rd part of upper rail section
Connector4 - 4th part of upper rail section
Grips - Grips for front end (need 4 of these)
Muz - Muzzle
MuzRing - Muzzle ring
FNub - Front Nubbin
Eagle - Eagle Emblem
FSight - Front sight
Rsight - Rear Sight
ChargeH - Fake Charging Nubbin
TMMagTop - TM compatible Magwell Top
TMMagBot - TM compatible Magwell Bottom
Assemble these parts to create Front End section 1 and glue (See image https://thingiverse-production-new.s3.amazonaws.com/renders/8f/df/9c/6d/3b/4175a38a32bbdcffdfbd120568a81e82_preview_featured.jpg)
FPlate - Front Plate
FrontSideL - Front Side Left
FrontSideR - Front Side Right
FGrip - Front Grip
Assemble these parts to create Front End section 2 and glue (See image https://thingiverse-production-new.s3.amazonaws.com/renders/7a/c8/e2/72/7f/77ae8c373087666dfa784e0bb3844616_preview_featured.jpg)
MidSideL - Middle Side Left
MidSideR - Middle Side Right
MidGrip - Middle Grip
RearSideL - Rear Side Left
RearSideR - Rear Side Right
*Note the part "ChargeH" needs to be fitted to the part "RearSideR"
Assemble both Sections and glue (See image "Front End")
Assemble these parts to create Top Rail Section 1 and glue them together into 1 single piece.
Connect1
Connect2
Connect3
Connect4
Ensure they are orientated correctly!
Assemble the parts to create Top Rail Section 2 and only glue the nuts into each segment. The segments must remain seperate!
RailA1
RailB1
RailC1
RailD1
Assemble the parts to create the magwell and glue
MagL - Left hand side of magwell
MagR - Right hand side of magwell
MagLA - Left hand side magwell part2
MagRA - Ritght hand side magwell part2
*MagTop - Top section to interface with SRC hop unit
*Exchange for the two parts below to chnage it from SRC compatible to TM compatible
TMMagTop - Top section to interface with TM Style hop unit
TMMagBot - Bottom section to interface with TM Style hop unit
(some filing may be required to get it to feed BB's correctly and allow the nozzle to pass)
Fit part: MuzRing into back of the frontplate, this will allow part: Muz to fit onto it
The part: FSight allows two nuts to run inside of it and is the screwed on from underneath so that it attaches to part: RailA1
(see images for clarification)
The part: RSight other than providing a rear sight helps to hold the front end flush to the G36 replica.
Special Notes:
The part: Grips can be fitted at your discretion and in any number (i used 4 evenly spaced.
The part: Eagle can be fitted at your discretion.
Please refer to images prior to gluing. Always double check parts. Some sanding/adjustment may be required.
Have fun
Remixes should be great fun if you can improve this model :)
https://www.facebook.com/wallopsoftmodels/
https://www.shapeways.com/shops/wallopsoft?li=pb
| Connect1.stl | 34.1KB | |
| Connect2.stl | 40.8KB | |
| Connect3.stl | 34.5KB | |
| Connect4.stl | 102.6KB | |
| Eagle.stl | 330.7KB | |
| FGrip.stl | 100.5KB | |
| FPlate.stl | 213.5KB | |
| FrontSideL.stl | 125.9KB | |
| FrontSideR.stl | 153.6KB | |
| FSight.stl | 243.8KB | |
| Grips.stl | 36.6KB | |
| MagL.stl | 264.3KB | |
| MagLA.stl | 51.3KB | |
| MagR.stl | 243.5KB | |
| MagRA.stl | 45.7KB | |
| MagTop.stl | 144.8KB | |
| MidGrip.stl | 76.4KB | |
| MidSideL.stl | 126.8KB | |
| MidSideR.stl | 139.3KB | |
| Muz.stl | 182.3KB | |
| MuzRing.stl | 86.7KB | |
| RailA1.stl | 308.0KB | |
| RailB1.stl | 142.2KB | |
| RailC1.stl | 216.4KB | |
| RailD1.stl | 213.5KB | |
| RearSideL.stl | 48.7KB | |
| RearSideR.stl | 46.9KB | |
| RSight.stl | 182.6KB | |
| TMMagBot.stl | 130.8KB | |
| TMMagTop.stl | 91.1KB |
