Light and sturdy carriage for ANET A8 converted to bowden E3D extruder.
You can select of variety clamps with fan mount and round 8mm,12mm, 17mm cubic inductive sensors or without a sensor or just a bare clamp for setups with fan(s) attached to E3D hot end directly. It looks awesome if printed of a temperature dependent color changing filament.
check out my other stuff for ANET A8 and enjoy!.
Fitting:
It uses original setup - bolts and nuts to attach X- belt, but positioned slightly higher to make the belt run linearly. It has 6 attachment points for zip ties. The clamp is attached with two M3 bolts and M3 nuts fitted in carriage slots for tight fit.
Print setup:
clamps - print upside down, 50-100% infill 1,2mm walls, no supports
carriage - 50% infill, 1.2mm walls no supports
nozzle - print solid, with supports touching buildplate only
material - preferably ABS, but PLA works fine for carriage too for open setup.
29/4/18
configuration.h file for Marlin 1.1.8 attached
run PID calibration of display after instalation and tune your Z offset
Calibration:
in configuration.h:
define X_MAX_POS 220
define X_MIN_POS -16
define Y_MAX_POS 220
define Y_MIN_POS -9
define Z_MAX_POS 240
define Z_MIN_POS 0
define X_PROBE_OFFSET_FROM_EXTRUDER 30 // X offset: -left +right [of the nozzle], for TSD E3D V5 carriage
define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle]
define Z_PROBE_OFFSET_FROM_EXTRUDER 0
define ABL_GRID_MAX_POINTS_X 3
define LEFT_PROBE_BED_POSITION 20
define RIGHT_PROBE_BED_POSITION 200
define FRONT_PROBE_BED_POSITION 20
define BACK_PROBE_BED_POSITION 200
define Z_SAFE_HOMING
versions:
clamp Bl touch - !prototype! please test and comment
clamps v6h and v6j - prototype for "ANET" blue cubic Z sensor
fan nozzle 5h - optimized high flow nozzle
clamps v6e and v6f - for 17x17mm cubic sender like tronxy or prefered TL-Q5MC1(works great at 5V ~4mm sensing distance). v6e is attached by two M3x25mm bolts, v6f is fixed by a zip tie. calibration X +30mm (right) of the nozzle.
clamp v6d - !prototype! for 12mm inductive sensor, calibration X +30mm (right) of the nozzle
clamp v5b no fan - optimized bare hot end without a bracket for a fan
nozzle v5 - high flow nozzle
clamp v5 - optimized clamp for 8mm inductive sensor, calibration X +30mm (right) of the nozzle
note: Please leave a feedback and proposals in comments.
clamp_BL_touch_c.stl | 66.4KB | |
clamp_v4.stl | 42.8KB | |
clamp_v5.stl | 54.0KB | |
clamp_v5b_no_fan.stl | 35.7KB | |
clamp_v6d.stl | 53.5KB | |
clamp_v6e.stl | 57.5KB | |
clamp_v6f.stl | 56.3KB | |
clamp_v6h.stl | 74.9KB | |
clamp_v6j.stl | 84.5KB | |
Configuration.h | 65.2KB | |
fan_nozzle_v5f.stl | 7.1KB | |
fan_nozzle_v5h.stl | 6.4KB | |
toosha_carriagev2.stl | 239.0KB |