Air Purifier 3D Printer Model
The file 'Air Purifier 3D Printer Model' is (bgcode,stl) file type, size is 112.6MB.
The file 'Air Purifier 3D Printer Model' is (bgcode,stl) file type, size is 112.6MB.
I suffer from hay fever, & have designed a air purifier to help with this. I've used the ubiquitous Ryobi paper filter, & added a HEPA pre-filter & a activated charcoal centre section which a 140mm Noctua 12v fan draws outside air through these filters exhausting clean filtered air from it's top.
This is my design solution for this.
I've included embedded hexagonal and square nuts which use M3 bolts to connect everything together..
I'm writing software to control this, & read sensors.
My previous designs here:
Buddy fan. https://www.thingiverse.com/thing:6737959
Pill Remover. https://www.thingiverse.com/thing:6624043
Tools Drawer https://www.thingiverse.com/thing:6472021
Autens Battery Charger https://www.thingiverse.com/thing:6367884
TS80P High Current Supply https://www.thingiverse.com/thing:6367814
Power Tower https://www.thingiverse.com/thing:6345056
Parts Caroursel https://www.thingiverse.com/thing:5343593
Dremel Jig https://www.thingiverse.com/thing:5267056
Containers for Carousel https://www.thingiverse.com/thing:5199867
Micro-Pump Housing. https://www.thingiverse.com/thing:5164094
Wire Bobbin. https://www.thingiverse.com/thing:4946929
Flux Funnel. https://www.thingiverse.com/thing:4946257
Large Spool Holder. https://www.thingiverse.com/thing:4816080
Tush Linear Bearings. https://www.thingiverse.com/thing:4815574
T-962 Modification. https://www.thingiverse.com/thing:4760915
Desiccant Funnel. https://www.thingiverse.com/thing:4716424
Arduino Mega Case. https://www.thingiverse.com/thing:4291794
Sandpaper Holder. https://www.thingiverse.com/thing:4213700
Gear Driven TUSH. https://www.thingiverse.com/thing:4196767
Tight-Fitting Container. https://www.thingiverse.com/thing:4158760
Power Supply Case. https://www.thingiverse.com/thing:4073804
**
After printing all parts
Parts List:
1 x Noctua 140mm x 20mm 12v fan
1 x AC to DC 12v converter
1 x Rotary encoder
1 x 1.8 inch TFT display
4 x M3 x 20r stainless steel bolt
8 x M3 x 10r stainless steel bolt
12 x M3 stainless steel hex nut
1 x M3 x 8 grub screw
I may at a later time use a MosFET & temperature sensor to turn the fan on automatically,
but at this stage, this is the simplest method.
| Base_cover_with_PCB_holders.bgcode | 1.1MB | |
| Base_cover_with_PCB_holders.stl | 3.0MB | |
| Base_with_nut_holders.bgcode | 5.0MB | |
| Base_with_nut_holders.stl | 4.6MB | |
| Central_pipe__nut.bgcode | 1.8MB | |
| Central_pipe__nut.stl | 2.1MB | |
| Fan_wire_conduit.bgcode | 1.0MB | |
| Inner_charcoal_holder.bgcode | 12.3MB | |
| Inner_charcoal_holder.stl | 74.0MB | |
| Outer_skin_with_nubs.bgcode | 15.4MB | |
| Outer_skin_with_nubs.stl | 75.9MB | |
| Top_lid.bgcode | 3.2MB | |
| Top_lid.stl | 4.7MB | |
| Top_with_nub_cutouts.bgcode | 2.3MB | |
| Top_with_nub_cutouts.stl | 1.8MB | |
| Wire_conduit.stl | 75.4KB |
