ACL Seed Pixel Strip System 3D Printer Model
The file 'ACL Seed Pixel Strip System 3D Printer Model' is (zip,stl) file type, size is 106.6MB.
The file 'ACL Seed Pixel Strip System 3D Printer Model' is (zip,stl) file type, size is 106.6MB.
This is a system for mounting seed pixels into a 3D strip which is then snap fitted to Deta 16mm x 10mm electrical conduit available in Australia in Bunnings stores in 4M lengths.
Each strip for the pixels is available in different unit numbers, a unit is a single pixel spacing. Most of the photos feature a 5 unit strip that is convenient to print and check fit. The strips are designed to actual sizes and you may need to print a couple of test strips to check your printer.
This also allows you to print the longest available strip that fits on your printer or mix and match strips to get near perfect window frames etc.
Example a 6U 25mm spaced strip will be 150mm long, a 6U 40mm spacing will be 240mm long.
All spacing sizes have a corner piece with the same spacing, they all are 2U long.
The system comprises the following:-
25mm spacing in 1U to 14U
30mm spacing in 1U to 14U
40mm spacing in 1U to 12U
50mm spacing in 1U to 10U
These all include the corner piece
Deta electrical conduit mounting solutions including flat, right angle, joiner, right angle to wall, DN15 and DN20 conduit clips, and two different gutter profile clips.
These have been tested with various 3 and 4 wire pixels but in all cases a test strip should be printed first and your seed pixels checked for fit.
Recommended way to insert seed pixels is to fold the wire over and push up then pull sideways in the slot, then push the pixel up and sit in place. It is easy once you do it a few times.
Untested but possible is the 25mm spaced strip should also mount 1" spaced seeds but will need to be tested and will be subject to accurate spacing by the vendor.
All parts can be printed without supports and are designed for minimal filament usage.
| ACL_Seed_Pixel_Strip_25mm.zip | 14.7MB | |
| ACL_Seed_Pixel_Strip_30mm.zip | 14.6MB | |
| ACL_Seed_Pixel_Strip_40mm.zip | 11.0MB | |
| ACL_Seed_Pixel_Strip_50mm.zip | 7.9MB | |
| ACL_Seed_Pixel_Strip_All_spacings.zip | 48.7MB | |
| Deta_Mounting_clips.zip | 493.0KB | |
| Seed_Snap_Strip_90_corner_25mm_spacing.stl | 1.8MB | |
| SnapStrip_25x10U.stl | 3.9MB | |
| SnapStrip_25x11U.stl | 4.3MB | |
| SnapStrip_25x12U.stl | 4.7MB | |
| SnapStrip_25x13U.stl | 5.0MB | |
| SnapStrip_25x14U.stl | 5.4MB | |
| SnapStrip_25x1U.stl | 705.4KB | |
| SnapStrip_25x2U.stl | 1.0MB | |
| SnapStrip_25x3U.stl | 1.3MB | |
| SnapStrip_25x4U.stl | 1.7MB | |
| SnapStrip_25x5U.stl | 2.0MB | |
| SnapStrip_25x6U.stl | 2.4MB | |
| SnapStrip_25x7U.stl | 2.8MB | |
| SnapStrip_25x8U.stl | 3.1MB | |
| SnapStrip_25x9U.stl | 3.5MB |
