This is the 6-pounder field gun of 1841 as it was used in the american civil war.
I tried to model as accurate as possible but some parts had to be slightly changed to make them printable.
I scaled it to about 1:12 so you can use the same wheels as for the "Cannon from Castle of Buedingen" https://www.thingiverse.com/thing:2546674
If you prefere to print the wheels in one piece you can take the Remix that was uploaded by "Intrudermax": https://www.thingiverse.com/thing:2812424
The drawing below was used as a template:
.
More historical information:
https://www.militaryfactory.com/armor/detail.asp?armor_id=660
Additional you need:
The two eye plates should be bowed about 45° to outside.
You can do it by warming them in hot water.
| axle.stl | 169.8KB | |
| axle_band_2.stl | 15.5KB | |
| barrel.stl | 1.8MB | |
| barrel_axle_.stl | 96.5KB | |
| barrel_breech.stl | 5.1MB | |
| capsquare.stl | 157.1KB | |
| capsquare_hook.stl | 31.9KB | |
| cheek_left.stl | 398.5KB | |
| cheek_right.stl | 398.5KB | |
| cheek_spacers_.stl | 530.4KB | |
| ear_plate.stl | 97.7KB | |
| ear_plate_hooks.stl | 1.6KB | |
| elevating_base.stl | 1.4MB | |
| elevating_handle.stl | 1.2MB | |
| eyelet_capsquare.stl | 26.1KB | |
| eye_plate_.stl | 177.8KB | |
| felloe_complete_2x_.stl | 160.6KB | |
| felloe_segment_12x.stl | 42.3KB | |
| hand_spike_rings.stl | 251.4KB | |
| hand_spike_ring_front_2.stl | 17.9KB | |
| hooks.stl | 1.3MB | |
| hub_2x.stl | 2.6MB | |
| hub_band_large.stl | 36.4KB | |
| hub_half_4x.stl | 1.9MB | |
| hup_band_small.stl | 36.2KB | |
| latch_capsquare.stl | 72.9KB | |
| linstock_socket.stl | 345.8KB | |
| M3_nut.stl | 608.7KB | |
| M3_nut_washer.stl | 802.4KB | |
| M3_nut_washer_hook.stl | 214.9KB | |
| M3_washer.stl | 497.0KB | |
| mount_hand_spike_ring_front.stl | 26.8KB | |
| spacer_hub_4x.stl | 108.6KB | |
| spokes_2x.stl | 3.2MB | |
| spoke_24x.stl | 554.4KB | |
| sponge_and_rammer_stop.stl | 68.2KB | |
| sponge_hook.stl | 591.6KB | |
| sponge_hook_plus_7_mm.stl | 593.4KB | |
| stock_left.stl | 412.0KB | |
| stock_right.stl | 412.0KB | |
| tire_brim.stl | 155.0KB | |
| tire_solid.stl | 30.0KB | |
| trail_handle.stl | 1.7MB | |
| trail_plate.stl | 972.7KB | |
| trunnion_plate.stl | 354.2KB | |
| under_strap.stl | 157.3KB | |
| wheel_guard_plate.stl | 141.9KB |
