28mm Miniature Boat Tiles 3D Printer Model
The file '28mm Miniature Boat Tiles 3D Printer Model' is (stl) file type, size is 2.5MB.
The file '28mm Miniature Boat Tiles 3D Printer Model' is (stl) file type, size is 2.5MB.
This is a set of tiles to make sailing ships/boats for 28mm miniatures. A 1-inch grid is modeled into the tiles to aid in gameplay. This uses a snap-together system for you to create ships as large or small as you like. Print out the tiles you want, print a bunch of connector pieces, then snap the connector pieces between the tiles until the whole stays together.
[UPDATE: Part 2 of this tileset is available here: https://www.thingiverse.com/thing:2776283]
Q: How well do these stay together?
A: They're a little wobbly, but not enough to throw off the game. You'll be able to push entire ships around without them falling apart. Picking a ship up is a delicate matter
Q: Do these need supports?
A: Most of them do, yeah. I use Simplify3D, so I was able to pick and choose where the supports went; you might not be as lucky with free slicers. If you do have something that lets you place your own supports, I recommend just leaving one pillar in the corner of the four corner connector holes instead of filling the whole thing; it'll bridge fine
Q: What did you print these on?
A: Printrbot Simple Metal, 1.7mm PLA, .3 layer height
Q: What did you use to design these?
A: TinkerCAD (https://www.tinkercad.com)
Q: Wait, the sails aren't printed, right?
A: Nah, that's muslin and thread
Q: How can you have a sailing ship without cannons?
A: I recommend this model: https://www.thingiverse.com/thing:2160741
Q: What happened to #10?
A: We don't talk about #10
Q: Does the wheel spin?
A: It should, though you'll have to carefully dislodge it at first. It's print-in-place after all
Q: What about a forecastle/sterncastle?
A: [Bane voice] "That comes later." Srsly, I'm working on it, but that's a whole other ballgame.
Q: Are those minis printed?
A: Nope; pretty sure all of them are from Reaper
| Boat_Tile_11_Large_Port_Bow.stl | 505.2KB | |
| Boat_Tile_12_Large_Starboard_Bow.stl | 505.1KB | |
| Boat_Tile_13b_Boarding_Railing.stl | 208.3KB | |
| Boat_Tile_13_Plank.stl | 56.2KB | |
| Boat_Tile_14_Half_Deck__Railing.stl | 247.2KB | |
| Boat_Tile_15_Yards.stl | 49.7KB | |
| Boat_Tile_16_Crows_Nest.stl | 982.9KB | |
| Boat_Tile_17_Small_Stern.stl | 632.7KB | |
| Boat_Tile_18_Boom.stl | 325.8KB | |
| Boat_Tile_1_Open_Deck.stl | 95.2KB | |
| Boat_Tile_2_Mid_Mast.stl | 118.3KB | |
| Boat_Tile_3_Double_Mast.stl | 584.9KB | |
| Boat_Tile_4_Railing.stl | 209.8KB | |
| Boat_Tile_5_Sharp_Corners.stl | 483.6KB | |
| Boat_Tile_6_Helm.stl | 1.4MB | |
| Boat_Tile_7_Ladder_Belowdecks.stl | 120.6KB | |
| Boat_Tile_8.5_Cargo_Grate.stl | 64.7KB | |
| Boat_Tile_8_Cargo_Hatch.stl | 57.3KB | |
| Boat_Tile_9_Round_Corners.stl | 510.4KB | |
| Boat_Tile_Connector.stl | 21.6KB |
